Im mounting a Premier 5-25x56 with a 34mm tube to a remington 700 SPS using regular low two piece weaver type rails.
Rifle Scopes what rings will work best for me?
- Thread starter the once-ler
- Start date
Re: what rings will work best for me?
I would ditch the weaver type rails and get a Seekins one piece base, then get a pair of Seekins rings. Likely their med-high would work on that setup.
I would ditch the weaver type rails and get a Seekins one piece base, then get a pair of Seekins rings. Likely their med-high would work on that setup.
Re: what rings will work best for me?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: jasonk</div><div class="ubbcode-body">I would ditch the weaver type rails and get a Seekins one piece base, then get a pair of Seekins rings. Likely their med-high would work on that setup. </div></div>
I run the same scopes on a Surgeons 591 short action and another rifle with a trued Remmy long action and use medieum height Badger Ordance rings on both. They are 1.125" or 1-1/8" tall and leave just over 1/8" or so clearance from the 56 mm bell of the scope to the rifle barrels. Just perfect in my book. I've herd some guys go with 1" tall rings but I think these were on smaller or factory coutour barrels. The long action I have has a Krieger # 9 contour barrel and the short action has a Bartlein #7 contour barrel.
One piece base as jasonk said and possibly a +20 MOA version would be good.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: jasonk</div><div class="ubbcode-body">I would ditch the weaver type rails and get a Seekins one piece base, then get a pair of Seekins rings. Likely their med-high would work on that setup. </div></div>
I run the same scopes on a Surgeons 591 short action and another rifle with a trued Remmy long action and use medieum height Badger Ordance rings on both. They are 1.125" or 1-1/8" tall and leave just over 1/8" or so clearance from the 56 mm bell of the scope to the rifle barrels. Just perfect in my book. I've herd some guys go with 1" tall rings but I think these were on smaller or factory coutour barrels. The long action I have has a Krieger # 9 contour barrel and the short action has a Bartlein #7 contour barrel.
One piece base as jasonk said and possibly a +20 MOA version would be good.
Re: what rings will work best for me?
so far i see they have .92 .95 .97 1" and 1.45" I want the tightest clearance possible and I am looking at the seekins rings
so far i see they have .92 .95 .97 1" and 1.45" I want the tightest clearance possible and I am looking at the seekins rings
Re: what rings will work best for me?
ok I found the Badger medium rings 1.125" ones you were talking about. where is the best place to buy these from? so I guess it would come down between the 1,125 and the 1" rings
ok I found the Badger medium rings 1.125" ones you were talking about. where is the best place to buy these from? so I guess it would come down between the 1,125 and the 1" rings
Re: what rings will work best for me?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Gappa</div><div class="ubbcode-body">ok I found the Badger medium rings 1.125" ones you were talking about. where is the best place to buy these from? so I guess it would come down between the 1,125 and the 1" rings </div></div>
I got one set for the first rifle direct from Badger Ordance and I got the second set from my gunsmith for the second rifle.
http://badgerordnance.com/34mm-scope-rings/
Mine are part # 306-61
Heres their 1 piece scope bases
http://badgerordnance.com/base/
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Gappa</div><div class="ubbcode-body">ok I found the Badger medium rings 1.125" ones you were talking about. where is the best place to buy these from? so I guess it would come down between the 1,125 and the 1" rings </div></div>
I got one set for the first rifle direct from Badger Ordance and I got the second set from my gunsmith for the second rifle.
http://badgerordnance.com/34mm-scope-rings/
Mine are part # 306-61
Heres their 1 piece scope bases
http://badgerordnance.com/base/
Re: what rings will work best for me?
ok fredrick so you are running pretty much the same setup? those were the ones I was looking at too 30661 but triad has them for 169 instead of 198
ok fredrick so you are running pretty much the same setup? those were the ones I was looking at too 30661 but triad has them for 169 instead of 198
Re: what rings will work best for me?
I run an S&B 5-25x56 which also has a 34mm tube and I use Seekins 1" height rings on a 20 MOA base and they give me plenty of clearence on my M40/M24 contour barrels. If you are running a factory Rem varmint contour they would work fine as well.
I run an S&B 5-25x56 which also has a 34mm tube and I use Seekins 1" height rings on a 20 MOA base and they give me plenty of clearence on my M40/M24 contour barrels. If you are running a factory Rem varmint contour they would work fine as well.
Re: what rings will work best for me?
Second what Rob says about the 1" rings. I have a Badger 20 MOA base and their 1" rings mounting a S&B PMII 5-25x x56 on my Rem 5R. About 1/8" of clearence between the barrel and Butler Creek caps.
OFG
Second what Rob says about the 1" rings. I have a Badger 20 MOA base and their 1" rings mounting a S&B PMII 5-25x x56 on my Rem 5R. About 1/8" of clearence between the barrel and Butler Creek caps.
OFG
Re: what rings will work best for me?
I ordered the seekins 20 moa base last night. But it looks like 1" rings are working well for you guys. Well this is bit of an enigma.
I ordered the seekins 20 moa base last night. But it looks like 1" rings are working well for you guys. Well this is bit of an enigma.
Re: what rings will work best for me?
I think it's gonna be a close match between 1" and 1.125" height. I wil have to wait till I get the base and scope in and try to measure out before I can do anything
I think it's gonna be a close match between 1" and 1.125" height. I wil have to wait till I get the base and scope in and try to measure out before I can do anything
Re: what rings will work best for me?
ok now all I need to know what the barrel contour of my Remington 700 SPS?? does anyone know?
ok now all I need to know what the barrel contour of my Remington 700 SPS?? does anyone know?
Re: what rings will work best for me?
Its the standard Rem varmint/sendero/700P contour. It says the low .92 height with that contour but I would go with 1 inch incase you ever rebarrel or put scope on another rifle with heavier barrel contour.
Its the standard Rem varmint/sendero/700P contour. It says the low .92 height with that contour but I would go with 1 inch incase you ever rebarrel or put scope on another rifle with heavier barrel contour.
Re: what rings will work best for me?
yea I think I'm leaning toward the 1" now and if they are too short I will go to the 1.125 badger rings. do you guys like the 4/6 type or the 4/4 type?
yea I think I'm leaning toward the 1" now and if they are too short I will go to the 1.125 badger rings. do you guys like the 4/6 type or the 4/4 type?
Re: what rings will work best for me?
ok I think I got it figured out now. the 20moa bases take up the extra 1/4" or so. so if I were using a flat or 0 moa two piece bases I would need the 1.125 rings.. Thanks for the help
ok I think I got it figured out now. the 20moa bases take up the extra 1/4" or so. so if I were using a flat or 0 moa two piece bases I would need the 1.125 rings.. Thanks for the help
Similar threads
