M
Latest activity Postings Featured content About Feedback Stats
-
-
MMustangGreg66 reacted to Dirty D's post in the thread Maggie’s Motivational Pic Thread v2.0 - - New Rules - See Post #1 with
Like.
-
MMustangGreg66 reacted to msgriff's post in the thread .223 Wylde Chamber in Trainer?? I don't get it. . . or do I? with Like.
I'll repost the following just for fun. Here's the text of a reply from Mr. Wylde regarding the .223 Wilde chamber: Posted By: Bill...
-
MMustangGreg66 reacted to Rob01's post in the thread .223 Wylde Chamber in Trainer?? I don't get it. . . or do I? with Like.
Yes it is by design so you can load the heavier bullets longer so they aren't shoved deep into the case and taking up powder area. I...
-
MMustangGreg66 reacted to AR shooter's post in the thread Charing handle popping loose - CMMG MK-3 308 with Like.
I had one doing the same thing. I compared it to another one and the latch spring was weaker. Put a new one on it and it stays latched now.
-
MMustangGreg66 reacted to cas6969's post in the thread Charing handle popping loose - CMMG MK-3 308 with Like.
As for fixing it.... I have a very old A1 upper that would bonk me in the nose often. Figuring I had nothing to lose, I took a teeny...
-
MMustangGreg66 reacted to memilanuk's post in the thread Why doesnt factory ammo have to chamfer the necks? with Like.
A counterpoint to what I said earlier about getting most of the neck tension from the sizing die, not from crimping: Years ago, Black...
-
MHere's hopefully the last update regarding the barrel nut issue. Outlier emailed me and said they were making me a new barrel nut, then...
-
MThe finish alone on the barrel is a tell tale sign it is no good. They threaded the tenon waaaaay too long, simple as that. sure it is...
-
MMustangGreg66 replied to the thread Charing handle popping loose - CMMG MK-3 308.Reading through their "Support" and partial warranty scared me away, but you're right. No harm in asking. I sent in a support message...
-
MMustangGreg66 reacted to msgriff's post in the thread Charing handle popping loose - CMMG MK-3 308 with Like.
Most large frame charging handles use the same latch spring as an AR-15 charging handle. If yours does, Tromix sells extra power AR-15...
-
MMustangGreg66 reacted to LRRPF52's post in the thread Charing handle popping loose - CMMG MK-3 308 with Like.
The Dremologist option will also cut away more into the anodizing, but you do have an angled surface now instead of a clean edge that...
-
MMustangGreg66 posted the thread Charing handle popping loose - CMMG MK-3 308 in Semi-Automatic Rifles.I have a CMMG MK-3 308 and when I shoot it, the charging handle is popping loose when it's fired and reciprocating, sometimes hitting me...
-
-
MMustangGreg66 reacted to semperfireloading's post in the thread AR15 223/5.56 Hornady 62 ELD-VT Reloads? with Like.
I loaded it into AR mags, no problem. I will have full review of it up in a few weeks. I loaded them at 2.300, which, at the case...
-
MMustangGreg66 replied to the thread AR15 223/5.56 Hornady 62 ELD-VT Reloads?.Hodgdon's load data lists 2.400" as the OAL, far greater than the AR mag length 2.260". So you'd have to single load in an AR or run it...
-
MMustangGreg66 reacted to spife7980's post in the thread AR15 223/5.56 Hornady 62 ELD-VT Reloads? with Like.
Good luck mag feeding it, the bullet is a mile long. 50 Sierra soft point, 75 bthp, 62edl-vt It liked the 23.2-23.8 gr 8208xbr same as...
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
