Recent content by 79M1a-texas

  1. 7

    SOLD Manners PRS TCS sikes and full arca weights

    still available?
  2. 7

    AR500 target gong thickness

    Looking for advice on proper thickness of target for 338 LM. Target distance will be 650 yards. Was hoping to find target in 3/4" thickness. Would a 1/2" target survive long term hits? Looking at 8" diameter size.
  3. 7

    US869 and 300 Win Mag

    All powders locally have dried up temporary. Have some Ramshot Mag being shipped in. Time to start over.
  4. 7

    US869 and 300 Win Mag

    Back from range withe the 300WM. Tried US869 cause H1000 has vanished from the free world. Use Federal military brass, 208 ELD-M and 250M primers. Couple of loads were under .5 MOA but velocity had a large spread. Crono was a Labrader. Even at the largest loads, no pressure signs. Will...
  5. 7

    US869 and 300 Win Mag

    I'm out of the H1000 and looking for a good starting point with US869 and the 300 WM. Using the 208 ELD-M bullet and hoping for the 2950 f/s range. What would be a good starting point powder weight?
  6. 7

    Reloading Equipment WTB: FC Military headstamp 300 WM

    thank you
  7. 7

    Reloading Equipment WTB: FC Military headstamp 300 WM

    Looking for 50 pieces of FC 300 Win Mag once fired brass with year headstamp. Will pay $35 shipped.
  8. 7

    Rifle Scopes 11126 USMC SCOPE RINGS

    I purchased a S&B scope that had some rings that were marked "11126 USMC" rings. Who makes these? The scope is a 34mm diameter.
  9. 7

    Atomic .308 Win Subsonic Powder Question

    I purchased a 50 round of this stuff and am getting .75 moa at 100 yards. Uses the 175g Sierra HPBT, Using a stock Remington 700P with a Yankee Hill Machine can. Very quiet. The COAL varies from 2.781 to 2.796. The powder weight is 7.40-7.46 g of a unknown powder. I would describe it as a...
  10. 7

    Subsonic .308 and Trailboss

    Thanks for the reply. Will re-test next weekend.
  11. 7

    Subsonic .308 and Trailboss

    Just got back from the range. Used the following Took LC Match brass and enlarged flashhole to 9/64" LR Mag primers, Trailboss @ 10.8g 220g RN Sierra #2180 2.810" COAL Remington 700 PSS Velocity as measured from Labrader - 2146 f/s Was expecting to see velocity around 1150 f/s. Wanting...
  12. 7

    removing tar from pulled bullets

    I am in the process of pulling the FMJ green tipped bullets from loaded ammo and switching to a non-FMJ bullet. What is the best way to remove the tar from the pulled bullets?
  13. 7

    Carbide Dies for Dillion RL550B

    Just purchased a used Dillon RL550B for my bulk .223 ammo for 3-gun events. Are the carbide dies worth the cost over the steel dies?
  14. 7

    Dillon 550B Question

    I use the Co-Ax and an arbor press for my precision 308 rounds. Just purchased a used RL550B for the .223 ammo for 3-gun. Are the carbide dies worth 3 x the cost of steel dies for bulk ammo?
  15. 7

    Ed Brown Light Tactical 308

    Re: Ed Brown Light Tactical 308 My first FTR setup was a A5 Tactical. Shot better then I could. At that time Ed Brown only made a 0 moa scope base so the fine guys over at Murphy Precision ( a site sponsor) made me a custom 20 moa scope base. Good luck.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts