Recent content by Boogaloo

  1. Boogaloo

    MDT (AICS) .223 mag WAY tight in my JAE chassis - Need Help

    I recently purchased a couple of MDT mags for my 223 AI to use in my JAE chassis and right out of the packaging, they basically need to be forced into place to engage the locking tab. I have a couple AI 223 mags that have been junk in this chassis from the get go, as I could never get them to...
  2. Boogaloo

    Small Rifle/Small Pistol - Ginex Primers Available now

    https://capitalcartridge.com/deal-of-the-week/
  3. Boogaloo

    What not to do.

    My take on this is there is no way in hell that an over pressure event caused that flash hole to nearly perfectly, symmetrically, open itself up due to excess pressure, or even the blast furnace method of hot gasses reverting back through the flash hole during ignition. If it did, there would be...
  4. Boogaloo

    H4350 in 223 AI ?

    Thanks @Haney H4350 is no bigger (kernel size) than Varget, and @ 26.4 grains, the top of the charge is right at the base of the neck/shoulder junction, so no compressed loads, yet pretty much precisely full enough for OBT consideration. Anyway, I appreciate the reply. I am going to load up a...
  5. Boogaloo

    H4350 in 223 AI ?

    I have recently switched back to my 223 AI barrel (223 wylde/223 AI switch barrel set up) and decided to investigate some different powders as I get back into the AI realm. I was running 2000-MR and CFE-223 as well as Varget and H4895 in my Wylde chambered for heavies, but with CFE-223 and...
  6. Boogaloo

    Accessories Bartlein 6mm blank trade for similar in 22 cal

    Don't have a 22 cal blank, but I do have a .308 Kreiger , 10 twist in heavy varmint I'd trade... I have a 6 comp match that I need to retire and would like to try a 6 Creed on for size. Just throwing it out there in case a 308 stick is in the cards for ya.... P.S. The blank is just shy of 30" @...
  7. Boogaloo

    Rock solid chassis!!!!!!

    Digging this up from the dead because I am wondering if anyone has any info about Todd and RockSolid Stocks? Did he stop manufacturing these?
  8. Boogaloo

    Firearms Looking to buy

    message sent.
  9. Boogaloo

    Range Report 6 Comp Match vs 6 Creedmore - What is the difference?

    Yeah, I have a 6 comp match hammer..... I really wanted more info on the fundamental differences between the 2. Chad likes RL26 now, but I am still shooting H1000... I will just ask Chad.... Thanks guys
  10. Boogaloo

    Kelbly Stolle Panda F Class rifle (6mm BR)

    I haven't been in here in almost a year... I come back in and see that LRI is still doing WORK baby!! Solid bad ass work! Good job Chad !!
  11. Boogaloo

    Surgeon Prefits?

    I can tell you that I have (3) Surgeon 591R actions, two of them built into complete rifles still up and running flawlessly to this day and one bare action that is sitting in my safe. I am happy to PM you the sequential serial numbers I have, which are from December 2014, when I took delivery of...
  12. Boogaloo

    Range Report 6 Comp Match vs 6 Creedmore - What is the difference?

    I dug around a bit, but I am coming up dry.... Is it just the neck angle that separates these 2 cartridges?
  13. Boogaloo

    Hornady OAL gauge - Need a couple of cases threaded... Anyone do this here?

    I'd like a link to where you see a case ready to purchase from Hornady in 6CM ? for the life of me I can't seem to dig one up. To everyone else, thanks for the tips!
  14. Boogaloo

    Hornady OAL gauge - Need a couple of cases threaded... Anyone do this here?

    Had a member offer to do this for me several months back and then he just disappeared off the face of the hide..Never did get the cases from him. Anyway, I need a .223 case and a 6 Comp Match case drilled and tapped for the Hornady OAL gauge. Anyone have the tap and willing to hook up a fellow...
  15. Boogaloo

    Rem 700 223 Pierced Primers

    You can also try a lighter weight F/P spring, or modify a stock spring by cutting one coil at a time to reduce the impact on the primer. It's worth a try, and stock springs are cheap... I actually really like the CCI 400 primers and I have a shitload of them, but I primarily use them as pistol...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts