Recent content by DangerRanger

  1. DangerRanger

    Hornady on Load Development

    I agree that I prefer litz for actual research
  2. DangerRanger

    Hornady on Load Development

    People so badly want reloading to be some type of incredibly hard Vudoo magic to figure out. My shooting experience got so much better when I stopped caring about all the reloading minutia and started just pumping out ammo with a decent bullet close to book max at a normal overall length...
  3. DangerRanger

    Muzzle Brake vs Supressor

    My imaginary confirmation biased mental data tells me that my can is about half as effective as a good brake at recoil reduction. If you want to free recoil off awkward barricades and watch your spots on a gamer gun a brake will do a better job. Personally, I find them miserable to shoot and...
  4. DangerRanger

    "Over Tightening" is a Problem?

    I think you’re over worried about it. Just don’t go full gorilla on it. I know people talk about hand tight with direct thread but there’s an interesting bit in cgs manual here: For normal use, very hand tight will do. For extended use, torque the Hyperion using the 7/8” wrench flats to the...
  5. DangerRanger

    AAC "SABRE BLADE BLACK TIP"

    We can’t know what happened, could have expanded inside and it’s laying dead 10ft from where you stopped looking. No way to know unless you do. The constant problem with bullet critiques without a dead animal
  6. DangerRanger

    What does 6.5 do over 7.62?

    It’s 2023 and we are still doing this. Feel like I’m in a Time Machine It doesn’t fucking matter shoot what you want. Walmart has both, there’s cheap shitty brass of both, there’s good stuff of both, the ammo for both is everywhere You’re gonna miss because you suck either way. Everything...
  7. DangerRanger

    16" 6.5 Creedmoor Options: Criterion vs Rainier Arms Match

    From what I can find the only 16” criterion 6.5 creed barrels are nitride, they offer 308 in 16” but I don’t see creed
  8. DangerRanger

    16" 6.5 Creedmoor Options: Criterion vs Rainier Arms Match

    Bump, any other options on this market? Looking at doing the same (16” “light” creedmoor)
  9. DangerRanger

    Can a Browning BAR MK3 barrel be threaded?

    I’d like to know more about this, that thing is sweet
  10. DangerRanger

    Rifle Scopes So, what about Leupold Mark 5 ?

    I know of 2 that went back for turret work and have an acquaintance that has seen a few more go down. I understand small sample size etc, people are gonna follow their heart, but Figured I’d mention the evaluations since you asked about durability now that they are out there.
  11. DangerRanger

    Rifle Scopes So, what about Leupold Mark 5 ?

    Rokslide evaluated 2 of them, one 5-25 and one 3.6-18. The reviews are easily searchable by “rokslide field evaluation mk5”
  12. DangerRanger

    Can a Browning BAR MK3 barrel be threaded?

    Who threaded yours? I’m looking at threading a mk3
  13. DangerRanger

    Vortex lht 4.5-22 durability test

    So far my trijicon has not had an issue with the same cold making the magnification ring unusable by hand. The problem wasn’t that it stiffened. The problem was it was so stinking tight to begin with any further stiffening made it useless Anyway I’ll bow out if this now, just seemed right to...
  14. DangerRanger

    Diligent Defense Enticer S

    It can but it’s a whole thing, it’s semi permanent because it’s a .670 barrel threaded 5/8 with almost no shoulder, so idk lots of work and I’ll still need to put a different taper mount back on. With the enticer I can just leave it as is and run a griffin hub adapter if the performance is equal...
  15. DangerRanger

    Vortex lht 4.5-22 durability test

    I think the parallax and mag ring, especially the mag ring is just specced too tight. Idk why they did it; the razor gen 3 magnification ring tension is buttery smooth. I’ve owned 3 lhts total and all the mag rings were incredibly tight Either way, is what it is.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts