Recent content by davwil

  1. D

    Quick Shot Challenge: Caption This Sniper Fail Meme

    Bench shooting is for pussies
  2. D

    Earlier Reaper IR red dot mount?

    That is decent solution. I’d prefer it on top but…. Thanks for the reply and information.
  3. D

    Earlier Reaper IR red dot mount?

    Has anyone figured out an easy way, or found an adapter for mounting a red dot on the Wilcox top mount of the earlier Reapers?
  4. D

    Rifle Scopes US Optics Question

    I just tried the above and apparently (or something certainly did) moving the entire erector does change the zero dramatically. I moved it per instructions and I was so far off target (30 inches) it took me awhile to find POI. I do think however after the adjustment I will have considerably...
  5. D

    Rifle Scopes US Optics Question

    Thanks PhrogDriver! I'll give it a try. It seemed way to easy and I didn't want to mess things up without asking first. Thanks again!
  6. D

    Rifle Scopes US Optics Question

    I just zeroed a new US Optics 5x25 scope with Erek elevation knob. I have a 20 MOA base. I have a few questions that I could use some help with. 1) The manual and the website says the scopes come set for maximum elevation with 20 MOA bases. After zeroing I have at about 2 full turns of...
  7. D

    Best Long Range Mountain Class

    Thanks....that's actually one I had looked at and considered.
  8. D

    Best Long Range Mountain Class

    I'd like to get out of the Texas heat this summer and want to take a beginner's long range shooting class....3 to 5 days....somewhere pretty and cool in the mountains. Any suggestions would be much appreciated. Thanks
  9. D

    Gunsmithing Recommendation for good taps and dies??

    Thanks cal50 and turbo54, this sounds like the way to go. I'm always amazed and appreciative at the experience, insight and advice that gets shared on this site. The hide has to have some of the most quality individuals on the planet. Thank you!! I'd buy you a beer if you were a little...
  10. D

    Suppressors Best Taps and Dies for Suppressors

    Man, the hide has saved me a lot of time and headaches and I appreciate everyone's response but obviously these aren't items most people buy. Apparently these fine threads aren't the norm and I knew that when I asked the question. Most of these suppliers don't handle these sizes and those...
  11. D

    Gunsmithing Recommendation for good taps and dies??

    It was a new suppressor and normally I check the threads first but I didn't and there must have been a small chunk of metal in the threads. I can see where it started to cut into the first couple of threads on the suppressor and it will only go on about 2 turns before it starts to hang up...
  12. D

    Gunsmithing Recommendation for good taps and dies??

    I have a bur I need to remove from a suppressor. Can anyone recommend a good source for quality 5/8" - 24 and 1/2" - 28 taps and dies. The ones from Midway don't look that good especially for the cost. Any recommendations/sources would be appreciated. Thanks.
  13. D

    Suppressors Form 4 wait time

    My last two have taken 6 to 7 months.
  14. D

    Suppressors Best Taps and Dies for Suppressors

    I need a 5/8" - 24 tap to clean out a bur in a suppressor. I'd like to go ahead and the 5/8" tap while I'm getting and also a 1/2" - 28 tap and die for my other suppressors. Maybe I should be asking this question on the gunsmith forum but, does anyone know where I can get some good hexagon...
  15. D

    looking for a nice bolt gun in 22

    Re: looking for a nice bolt gun in 22 cz452 for sure
See more
Top Bottom
Back
Home
Forums
Merch
Alerts