Recent content by Deltagunner00

  1. D

    Lee “Kit” Press to MEC Marksman

    Been making ammo for years on an old Lee Kit press. Looking for a little better consistency, or areas to upgrade my reloading room. Will I notice a difference in upgrading from the Lee to the MEC Marksman? Mainly loading 6BR for PRS and 243 for coyotes. Just looking for input. Thanks!
  2. D

    6mm BR

    Appreciate it. I have cleaned it well. What is recommended for polishing?
  3. D

    6mm BR

    Please notify me or correct it if this needs to go elsewhere. I have a Redding Competition Seating Die. Seats fine, but it gars/scars up my 105 105 Hybrids. What is the best way to correct this or polish this up? Or, would I be better off getting a different seating die? Honestly, I...
  4. D

    Optic Reccomendation

    Looking for some input on a budget minded optic for a 6.5 Grendel. Budget is in the $700 range. Background; have used this rife a ton in the past with thermal to shoot lots of coyotes. My main coyote rifle is now a AR10 in 243. I want to use the Grendel more now for mid range use at 450 -...
  5. D

    PRS Talk PRS Tactical 308

    It was great! I only used my 308 for 3 matches, just to be sure I liked it. I was hooked immediately! It’s a blast! I put together a 6BR and have used it the last couple of matches.
  6. D

    PRS - Shooting with Hand on Scope

    I did this. Just kinda weird about liking my rings centered up. Didn’t know if anyone had tried to shim the pic rail up a little. I’ll just run it the way it is with optic forward
  7. D

    PRS - Shooting with Hand on Scope

    It is the long board.
  8. D

    PRS - Shooting with Hand on Scope

    I went with the Hawkins. The diving board / pic rail hits and sets on the bell of my scope. Vortext Razor Gen II. Anyone else ran into this?
  9. D

    PRS - Shooting with Hand on Scope

    Have you tried/compared the Hawkins against the Vortex Diving Board? Trying to figure which route to go since I already have the Vortex rings that go with the Vortex diving board.
  10. D

    PRS - Shooting with Hand on Scope

    Any chance you have compared the Hawkins Rings to the Vortex Diving Board? Just trying to decide which route to go. Thanks
  11. D

    PRS - Shooting with Hand on Scope

    On a lot of positional stages, I feel most comfortable with my hand on the scope, rather than extended, clinching the bag and side of my chassis. Right now, I just have regular rings and my bubble level there where I put my hand and it's kind of hard to get the same hold each time. Would I...
  12. D

    New Trimmer Advice

    Currently: I am now using the LE Wilson trimmer followed up by the RCBS trim center to chamfer and debur. Works fine but just so slow. Upgrade: Looking at possibly a Giraud or maybe just the Tri Way and a cheap bench grinder from Harbor Freight. Not looking to shell out the money for the...
  13. D

    IDTS?

    Reviving this thread. Good info. I was deciding between the two. Thought I wanted the IDTS as I like the stand. I got out a Vortex scope cap and can't get it on the end of my Vortex Razor Gen II due to clearance over barrel. Is the cap that comes with IDTS similar? If so, guess my option...
  14. D

    243 - Cycling Issues

    Buddy has a 243 that I am helping him with. It will sometimes cycle a few fine and run fine, but then run into issues. It will feed the next round in just fine, but it seems like the BCG is not going forward far enough or the trigger is not being reset. When you pull the trigger the next time...
  15. D

    Official MDT 6BR Magazine Thread

    Any updates on this? Have a 12 that is a PITA to get 10 or so in. I will say, it is new and letting it soak for a week or so at full capacity.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts