Recent content by FourT6and2

  1. FourT6and2

    Exploding Pagers neutering terrorists.. Mossad operation?

    Saw some video from hospitals filled with these a-holes. It was brutal. Pagers went beep beep, Hezi terrorist takes it out to look at it and it blows up in his face, taking his hands and eyes. Saw others with holes blown through their sides, where they were wearing the pagers. Looked like 4th of...
  2. FourT6and2

    Defiance 40% off

    New logo looks like it was designed by someone with too many tribal tattoos.
  3. FourT6and2

    Anyone drive a Rivian R1T?

    I know someone who works at Rivian and has let me drive a few. They're not bad. The one thing I dislike about them is the regenerative breaking. You can't turn it off, only set it to low. So you can't really coast in them. You let off the throttle and it breaks. Very annoying and causes the ride...
  4. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Yeah, my gunsmith just sent me video of Impacts and Terminus doing the same exact thing. I'm not concerned anymore. Two things are happening: 1. The detent in the bolt body ramp, that the cocking piece rides into and out of, is shaped a little differently on every model of action. My Defiance...
  5. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Jon Beanland gave me a call immediately after sending him the video haha. He said it's 100% normal and that every single Fuzion and even Impacts and Terminus he's built has done it. It just depends on the trigger used and how long the sear is. He said these companies build these actions with...
  6. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    You know... it's happening upon extraction as well, at the same exact spot. So I think it has something to do with the detent in the bolt body ramp that the cocking piece rides in/out of.
  7. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Jon Beanland. Just sent him a message
  8. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Interesting. I don't know how or where the shroud could be hanging up on something, but I'll have a closer look.
  9. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Makes sense. I don't notice any. Yeah, first thing I did was clean and re-lube. I'll take another look Yeah, I do like hangers sometimes. I'm not a huge fan of BnA, though. But I figured I'd give this one a try. My Jewel triggers have run flawlessly for almost a decade. I had a problem with...
  10. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Go to 8:13 in the video. He runs the bolt a few times and it looks pretty smooth to me. Not at all like mine.
  11. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Also, when opening the bolt to extract... it's not a smooth extraction either. The same point where the snap happens on close, it happens on open as well. So opening the bolt feels like three separate motions. A bit awkward.
  12. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Yes, exactly. When you run the bolt at normal speed, it's still very much there. It's more than a small "click" lol. It's a rather abrupt and violent snap. So much so, that the bolt shroud and bolt handle actually move.
  13. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    It's not really about running the bolt too slow or looking for a problem that isn't there. When you run the bolt at normal speed there is still a very prominent audible and tactile click—like a trigger break—half way through closing the bolt. It's not a smooth action. It's like hitting a speed...
  14. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    Lone Peak shipped out a new cocking pice/firing pin assembly. Will just need to figure out how to remove/replace
  15. FourT6and2

    Lone Peak Arms Fuzion: Cocking Issue?

    But yours does it too? i.e. there's a sudden click part way through the cocking action as you lower the bolt? I've just never seen this before on a 700 clone.