Recent content by Hoser

  1. Hoser

    Vudoo closed the doors…

    As long as they don’t get into pistols they will be fine.
  2. Hoser

    A more quiet suppressor on a 50 BMG rifle ?

    That is a standard AI-ELR barrel. 28 inches I think. I am leaning towards shorter next time.
  3. Hoser

    A more quiet suppressor on a 50 BMG rifle ?

    I have a Thunderbeast on my 50. It was absolutely worth it. Everyone that shoots my 50 smiles and agrees that the recoil was not bad at all. Everyone that hears it says it sounds like a suppressed 308. Amazing can all around. When this barrel is toast, I will have to think about what length...
  4. Hoser

    Looking For a .22 LR Barrel Chambered for .223

    The OEM barrels are. My aftermarket Bully (Ray-Vin) barrel is a 1-8.
  5. Hoser

    Looking For a .22 LR Barrel Chambered for .223

    My S&W Model 41 Bully Barrel is a 1-8 and it is a hammer. Small critters and tin cans inside 125-150 yards are easy. But I would not take it to a PRS Match.
  6. Hoser

    Sidearms & Scatterguns Getting into wheel-guns: S&W 986 or 627 PC / V Comp?

    The Titanium cylinders do show grime pretty fast compared to steel cylinders. I dont even clean the outside anymore.
  7. Hoser

    Sidearms & Scatterguns Getting into wheel-guns: S&W 986 or 627 PC / V Comp?

    I have all three of the above and a couple 929s. The only problem with the above 9mm revolvers is that you have to use moon clips. And some flavors of brass like Remington have under spec extractor grooves which means brass can easily fall out of the moon clips. Thats bad. But that is the...
  8. Hoser

    Dillon Super 1050/RL1050/RL1100 Loading

    Get these and dont look back. I have put them on all my Dillon measures. https://dramworx.com/products/dillon/
  9. Hoser

    Short-Bus

    I have been trying to get in touch with Braden at Custom Gun Coatings. @Short-bus I have emailed and sent PMs. Does anyone have a phone number or some other way to get in touch with him?
  10. Hoser

    Is it worth reloading precision ammo on a single stage versus progressive press?

    Yes. When the case pops up through the top of the toolhead, I just place an MTM funnel/droptube and pour in the powder. It is painless.
  11. Hoser

    Is it worth reloading precision ammo on a single stage versus progressive press?

    I load all my precision ammo on a 550 with powder that is coming out of a Prometheus or an autotrickler. Everything from 17 Mach IV to 338 Lapua. Less time at the bench means more time at the range. So far I have have not seen anything on the target or over the chrono that says "You have to...
  12. Hoser

    Suppressors 300 blackout sub/super ar suppressor

    I am using a Thunderbeast Ultra7 on my 300 Whisper/Blackout M-16RR. It is plenty quiet even when I use AA1680 for a powder which is on the louder side of things. Semi autos are not that quiet compared to bolt guns. No way around it. Checking numbers pre-Garmin...
  13. Hoser

    Starting a small casting company - need feedback

    For sure powder coat your bullets. Traditional lube sucks in comparison.
  14. Hoser

    Dillon Super 1050/RL1050/RL1100 Loading

    I was working on my 223 Ackley loading marathon on my Dillon 1100 when I learned something new. After 25+ years of loading on these machines, a new curve ball. My machine started getting stiff and I traced it to the primer slide. I thought the track was dirty. After cleaning it with acetone...
  15. Hoser

    Anyone Shooting a 40x?

    I have a couple Elrod 40X repeaters. I am very happy with them. They can easily hang with my Vudoos.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts