Recent content by jet_lagged

  1. J

    Other Demil/Pulled Bullet Sellers Besides American Reloading?

    https://www.gibrass.com/ http://www.patsreloading.com/ Wideners used to have pull and mil surplus, it I haven’t seen any recently. https://www.wideners.com/
  2. J

    What 224 bore supressor should I get for a Remington XP-100?

    I went with the OCL Polonium K for the 10.3 AR. Seemed to have a very good review on short barrels and is reasonably light. Came with a Ti HUB. https://pewscience.com/sound-signature-reviews-free/sss-6-95-ocl-polonium-k-mk18-556
  3. J

    Vehicle hail damage question

    My best guess it that they will total it for the body damage. They may offer to let you buy it back, but it not, ask them if you can. If they say no, then find out who they are selling it to. There are two big companies that do auctions for totalled/stolen vehicles. It may take it a few...
  4. J

    Weird looking brass

    Heavily fluted chamber to aid extraction? HK-91 or LaRue OBR with "xtraxn". (SVT-41 also in 7.62x54R)
  5. J

    anybody else do this? (case lube and primer pocket cleaning novel ideas)

    When I occasionally clean primer pockets, I also use the uniformer tool. If using motor oil type fluid for lube when case sizing, how do you get it off? Toss the brass in a pot of boiling water a couple of times, or ???
  6. J

    NOW I REMEMBER WHY I LOVE MY DILLON CARBIDE DIES

    DIY yourself a stuck case remover, if you already have a decent sized tap sitting around? Drill out the primer hole, tap/thread that hole, then use washers and a bolt with a wrench on it to exert tension against the bottom of the die to pull the case out
  7. J

    WTB Custom TBAC brakes

    https://www.snipershide.com/shooting/threads/srs-titanium-cb-brakes.7224855/
  8. J

    Fake reloading supplies company? reloaderscenter.com

    But no Fed LR Magnum primers! A scam, as I doubt they have the 999 8lb bottles of Magpro that is in my cart for a cool 250K.
  9. J

    SOLD WTS AI AT 6.5CR with case and Harris bipod - Reduced

    PM sent to purchase. Feedback: Rifle arrived in its case with accessories as advertised. Good comm. A smooth transaction.
  10. J

    5.56 AR Only Loads

    24.3gn of Ar-Comp with milsurp 62 gn steel core gave me right around 2750fps out of an 18” barrel. You should be able to go higher with lead core. I was surprised that the velocity was so low, as this is nearly the same speed as my 77gn load using Ar-Comp.
  11. J

    SOLD WTS ARISAKA 18350 WML

    I'll take it.
  12. J

    Headspacing on 2 different AR barrels: need some input:

    Have you tried swapping a few bolts around to see if that would make the headspace closer together? Could be an easier option….
  13. J

    OT: 300PRC and 6.5CM silencer recs

    Just got a TBAC Magnus (HUB mount) for use on my .300 Win Mag after doing the research, with the possibility of a .300 PRC rebarrel in the future. I’m very impressed with it. For the 6.5, it would be worth considering the Otter Creek Labs Hydrogen.
  14. J

    SOLD PRI Gasbusters

    I’ll take them.
  15. J

    Advice Needed

    Sell it as-is, but with the caution that is for component use only. You frequently see dented or blemished ammo on GunBroker listed that way.