Recent content by jmtyndall

  1. J

    Optics Bushnell Elite 3200 10x40

    Someone sent me a PM about this and reminded me I still have it haha. Anyways, if there's interest, I found it in the safe.
  2. J

    Optics Bushnell Elite 3200 10x40

    Forgot about this. I'll come down to $175
  3. J

    Optics Bushnell Elite 3200 10x40

    Dropped the price
  4. J

    Optics Bushnell Elite 3200 10x40

    Selling off my starter scope to free up some funds for the new baby in the family. Scope is a Bushnell Elite 3200 10x42mm with 1" tube. MIL clicks, MIL dot reticle. Also included are 1" TPS aluminum rings and butler creek caps. Decent little starter setup. Asking price is $200 shipped in the...
  5. J

    Shoulder Bump Question

    I think you're misunderstanding. OP is saying that with the +0.010" shell holder he is getting 0.007" of shoulder bump back. His target is to get 0.002" of shoulder bump. The shellholder set he is referencing only goes down (+0.008", +0.006" etc) so he will get more shoulder setback by using the...
  6. J

    Is there a way to find FPS without a chrono?

    You either need to know BC or velocity. Some BC measurements have been made that would get you reasonably close using the method above Sent from my LG-V410 using Tapatalk
  7. J

    I can't believe I went this long without...

    I waited 3 years. I bought one and had to ask myself why I was such a cheap azz for 3 whole years. Major improvement Sent from my LG-V410 using Tapatalk
  8. J

    RCBS 6.5 Creedmoor Die - worrisome ring on brass...

    Is it visual or can you feel/measure it? I see this on most rifle brass I size and its visual only for me Sent from my SAMSUNG-SM-G920A using Tapatalk
  9. J

    Anyone using the new Lapua 6.5 Creedmoor brass???

    A guy on another forum is seeing blown primers at lower velocities with Lapua brass than with Hornady. Just another data point Sent from my SAMSUNG-SM-G920A using Tapatalk
  10. J

    Efficient primer crimp removal?

    I like the rcbs cutter myself. It has a small angled cutter, and won't cut too deep and weaken the case head, and it's relatively fast Sent from my LG-V410 using Tapatalk
  11. J

    Ammo storage and humidity levels

    35% is really not high humidity levels. RH is not the problem, dampness is. Don't store ammo flat on your pourous concrete floor, and don't let water seep in and pool, you won't have any issues
  12. J

    Speed up your powder weighing with a GemPro250

    The other thing you can do it aim a camera at the pointer, which eliminates parallax error. You could even just use your cell phone camera and prop it up so it's looking right at the pointer
  13. J

    Getting into wet tumbling. What all do I need?

    Actually don't bother with pins. Get the stainless steel chips. They won't stick in cases or flash holes. Dawn and Lemishine(can get citric acid too, basically the same stuff)
  14. J

    Load data on military 308 sniper rounds

    From what I've seen FGMM 7.62x51 should closely match MK316 MOD 0, the replacement for M118LR. I think M118LR should be RL15 and not 4064 anyways. MK316 I think is supposed to be 40-50fps slower, and more temp stable, which may explain you seeing up to 100fps difference Edit: Actually it...
  15. J

    Gunsmithing Blueprint Remington 700

    Tagged for interest Sent from my LG-V410 using Tapatalk
See more
Top Bottom
Back
Home
Forums
Merch
Alerts