• Winner! Quick Shot Challenge: Caption This Sniper Fail Meme

    View thread

Recent content by MJP68

  1. M

    Reloading equipment -- what else do I need?

    Personally, as a starter Id purchase a regular scale and powder measure. .308 usually requires a lot of case prep if using mil spec brass so it saves wear and tear on the wrists to buy a case prep center and the needed attachments. tumbling in dry media works fine and vibratory case cleaners...
  2. M

    Tools to measure AR-10 chamber and 308 brass for custom sizing?

    I use the SB dies, and check headspacing with the Hornady set.. as far as actual chamber measurements on your rifle, sorry I don't know Are you having issues with your current reloads?
  3. M

    Comment regarding POF, did I make a mistake!!!!

    Which trigger did your POF come with? single stage I'm guessing while your RRA likely had their very good 2stage oe trigger.. just a thought POF usually uses the best components available during production.. and have shipped rifles with several different trigger configurations.. I own POF and...
  4. M

    Reloading for semi-308 differences?

    I struggled with hand loads for my semi auto .308 for several months, most manuals for .308 loads are based on bolt rifles.. as stated already start at least 2gr below min and work up or down from there. I use the small base dies in my single stage. As far as acquiring brass with a known...
  5. M

    XM80C Product Specification Sheet & Round Information

    good info, thanks
  6. M

    Wilson Combat barrels?

    Thank you for the correction, I ASSumed they were one and the same.
  7. M

    Wilson Combat barrels?

    The original barrel in my RRA is a Wilson 16" hbar non chrome lined. My only bitch is the weight, accuracy is probably better than it should be.. 3600 rounds so far
  8. M

    Upper for POF lower.

    Just adding my 2c, glad to help keep in mind the GAP uses gas impingement and as you already know POF uses their piston system POF also has uppers on sale... just a heads up, not trying to swing you one way or another A GAP .243 upper might get my attention for the right price:)
  9. M

    Upper for POF lower.

    I think they only list complete rifles on their site. they also use the same monolithic rail system as POF as well as the receivers
  10. M

    Rifle Scopes Scope mount recommendation

    PEPR, cant beat the price
  11. M

    Which primers for 223

    Federal 205M are my choice, but have been using CCI 400 1 slam fire out of 3000, yes the CCI #41 are thicker and designed for 5.56/.223 AR style rifles
  12. M

    Upper for POF lower.

    The P308 lower should fit any DPMS "style" .308 upper However the rear takedown pin is a standard AR15 size, not sure what brands of uppers use the smaller rear pin. Use any standard AR15 LPK to complete your build on the lower (it will also come with the smaller rear takedown pin) as the...
  13. M

    Rock River Arms 7.62x51 rifles. Much needed improvements ASAP!

    Came really close to purchasing a LAR8 2 years ago, 1100 for a 20" A2 stock, flat top upper. sounded like a smoking deal till I checked into the mods I would want mags were an issue but the proprietary barrel nut and handguards put it beyond what I wanted to spend. Judging by the shipping eta's...
  14. M

    Long Range Semi Piston Rifle

    http://www.snipershide.com/shooting/snipers-hide-semi-auto-rifles/234062-pof-14-5-308-850-yards-holy-s%2A%2At.html hope that helps.
  15. M

    swage vs chamfer primer pocket

    I chamfer as well. RCBS case prep center, but running a decrimp bit in a drill would be cheaper both are hard on the hands
See more
Top Bottom
Back
Home
Forums
Merch
Alerts