Recent content by Ritterbruder

  1. R

    WTB: Ruger American Predator OEM Stock with AI magazines

    I am looking at replacing the stock on my old Ruger American Predator with one of their new AI-magazine stocks. If anyone has an OEM takeoff that they’re looking to sell, please PM me.
  2. R

    6.5x55

    RL-26 is probably too slow, especially for your barrel length. RL-23 or H4831(sc) are still the best choices. You can also use RL-16 or H4350 and get great velocities, but your load density would be low.
  3. R

    6.5x55

    Another military load in case someone is interested. This one was capable of MOA accuracy with iron sights in two Swedish Mausers (M96 and M38). Lapua Brass CCI #200 Primer Alliant RL-23, 46.2 gr Hornady 140gr BTHP Seat to 2.600" base-to-datum with Hornady comparator (~10-15 thousandths off...
  4. R

    6.5x55

    I just completed some load development for the Swedish Mauser and thought I'd share my results. This load shot well in a '43 Husqvarna M96 long rifle (29' barrel) and in a '41 Husqvarna M38 short rifle (24' barrel). Lapua Brass CCI #200 Primer Alliant RL-17, 42.1gr (warm load) Hornady 140gr...
  5. R

    New to reloading 6.5 Creedmoor, question about velocity

    100 fps gain for a 60°F increase seems a bit high for H-4350. It's supposed to be one of the less temperature-sensitive powders. http://precisionrifleblog.com/2016/06/19/powder-temp-stability-hodgdon-extreme-vs-imr-enduron/
  6. R

    Neck getting thicker

    I believe I fixed the issue. It seemed like a QC issue where the case mouth was a bit thicker than the rest of the neck. I used a 0.261" mandrel to uniform the neck and use a chamfer/deburr tool to trim off the excess. Took 2 firings to get it uniformed.
  7. R

    New to reloading 6.5 Creedmoor, question about velocity

    4064 and Varget burn a bit too fast for 6.5 Creedmoor. You will overpressure the case before you get your velocity to where you want to be. You might have some luck with lighter bullets, but certainly not for 140's. As a general rule: the smaller the caliber, heavier the bullet, and larger the...
  8. R

    New to reloading 6.5 Creedmoor, question about velocity

    Nope, thank YOU for sharing because I was beginning to wonder if I was alone ;)
  9. R

    New to reloading 6.5 Creedmoor, question about velocity

    I also have a factory Tikka CTR 24” 6.5CM. Brand new gun with only 230 rounds through it. My load is with Lapua brass, 140 ELDs, and CCI #400 small primers. I tried H-4350 and RL-17, and I was getting pretty low velocities too compared to what others are getting. With H-4350, 41.5 grains gave...
  10. R

    Neck getting thicker

    I am using Redding Competition Dies with a 0.290" bushing to reload Lapua 6.5 CM brass. My loaded rounds measure 0.292-0.293" on the outside of the neck, so the 0.290" bushing should be fine. This worked fine for the first two reloads. On the third, I noticed a lot of neck tension and copper...
  11. R

    Finnish M39 - struggling with seating depth

    Mine's a 1967 "sneak". I believe Sako made those. I was going to try the Hornady 174 FMJ next. The cannelure is located pretty far forward on those right?
  12. R

    Finnish M39 - struggling with seating depth

    I have a Hornady OAL gauge, but I don't have a modified 54R case to use with it. I did try to push the bullet back by jamming it into a case, and it ended up at around 2.330". I seated a few bullets to 2.310" and I still get scrape marks.
  13. R

    Finnish M39 - struggling with seating depth

    I've been trying to work up a handload for my Finnish M39 Mosin Nagant, and I am struggling to make sense of why my bullets keep touching the lands. I took a factory PPU round and measured the base-to-datum at 2.437" (with a Hornady bullet comparator). The PPU load uses a 0.310" diameter...
  14. R

    Tikka T3 Thread

    I got my MDT magazine in today (without the binder plate). The rounds will get stuck under the feed ramp, but they don't get stuck on the way into the chamber. They get stuck when the round is moving up into feeding position. It looks like the follower is tilting and the bullet is nosing down...
  15. R

    Tikka T3 Thread

    Thanks, I think I'll first try with the MDT metal magazine without the binder plate and see if that works for me. I asked MDT and they always include a disclaimer saying that you might need to grind off part of the feed ramp so the bullet tips don't snag.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts