Recent content by Slu54

  1. S

    M40A5 clone question: machined-in pillars or bed pillars?

    option from mcmillan, either have the preinstalled pillars or leave larger holes to bed pillars later (like the ones that come with the m5 dbm). I just want to know what would be more "correct"
  2. S

    M40A5 clone question: machined-in pillars or bed pillars?

    Just a question I hope some of ya'll know, if I want to be as true to the PWS way as possible, did they use the stocks with machined in pillars or did they bed pillars in? Just want to be sure before I click send on a stock order.
  3. S

    WTB [WTB] LaRue LT840H-34-20

    Up
  4. S

    Feedback Avoid Fraud With This Feature

    Unbelievable: this scammer photoshopped a timestamp onto a photo from a legit listing on another site 3 years ago: His PM to me: Original post he took it from: Account joined 11 years ago, first post a month ago, all read like they're AI generated. Definitely compromised account. Watch out...
  5. S

    WTB [WTB] LaRue LT840H-34-20

    Thanks.
  6. S

    Leupold MARK 5HD 2-10x30

    Eh, I'd like the smaller scope, matters to me. I don't want to get much bigger than an ATACR 1-8 or I'm just going to stick with that.
  7. S

    SOLD Leupold Mark 5HD 2-10x30 TMR Illuminated

    Still avail?
  8. S

    Leupold MARK 5HD 2-10x30

    its bigger with a bigger objective that gets in the way of shit in the front, doesn't it?
  9. S

    Leupold MARK 5HD 2-10x30

    Still waiting on better reticles and a tan version but would replace 1-8s on a couple of short 308 gas guns. Wish it was more like 3-15 in the same form factor.
  10. S

    AXSR stock collapsing under recoil?

    Yep, that was it. Fixed. Thanks.
  11. S

    AXSR stock collapsing under recoil?

    So I took apart the levers and put them on again, I might've done it wrong. The LOP adjust collapses if I hit it hard enough. I've tightened the screw to the point where it's very hard to disengage the lever, but if I hit the stock hard enough it'll still collapse. I also noticed the LOP...
  12. S

    AXSR question: is action bonded?

    I'm not sure if it is Paul's I got it from MHSA. I can't see to get the factory one off without taking the action out, what's the trick?
  13. S

    AXSR question: is action bonded?

    I want to replace the trigger shoe with a flat face one. The way it's designed you can't do that unless you pull the action out of the chassis (if I'm wrong tell me). Does this thing come off easy if I just take out the 5 action screws, or is it bonded? Thanks.
  14. S

    AW mag feed issue - 6CM Zeus QC + MDT ACC

    Setup is Zeus QC SA LH, MDT ACC LH, Proof prefit 6CM. Factory Hdy 108 ELDM I'd like to re-use the AW mags I have. Feed fine from the right side of the magazine (follower is lower) but jams from the left side (follower is higher), round hits the wall of the receiver it looks. If I tap it after...
  15. S

    WTB FOUND: Looking for a Badger Raptar/RULR mount, 34mm, for the legacy rings

    ARFCOM username TheTank140 has one as of 3 weeks ago, you can try him
See more
Top Bottom
Back
Home
Forums
Merch
Alerts