ARC, 419 and Audere out of the ones I own.
I have a handful of Spuhrs but I’m resigned to the face they’ll crack at some stage.
I have a handful of Spuhrs but I’m resigned to the face they’ll crack at some stage.
-
Having trouble using the site?
Contact support
Spuhr, ZCO, now A419 mounts
- Thread starter FNG1001
- Start date
Does some one know the reason, what cause the Spuhr top ring to get broken?
I have had Spuhr mounts, never had issue with mine´s, but have heard this.
I have had Spuhr mounts, never had issue with mine´s, but have heard this.
Whoa, when did this happen? I've only heard of the clamping bars as well, rings are a first for me
I just purchased the new "low" diving board for the 419 mount I'll let you know how it works out and if issues are resolved.
@NLivingston do you know if there’s plans to make a cap for the match rings that will allow for the use of the diving board? Cause I’d buy it 
@NLivingston do you know if there’s plans to make a cap for the match rings that will allow for the use of the diving board? Cause I’d buy it
Its been asked for, I dont think there are any immediate plans at the moment though.
Just got the new short diving board for the Area 419 mount. It’s a definite improvement on my set up as it allows me to grab the entire turret and dial freely unlike the high version. For my new S&B 6-36 users you will still have an issue with the turret lever on the lock position as the diving board still obstructs operation on this setting. It’s not really an issue for me since I never really lock my turret but if this is important to you and you need fast access to your lever to unlock I suggest you look at different options.
Attachments
Why are y’all using Raptar mounts / “diving boards !”?
A hand hold ?
I fell like 1% of ppl with them actually have a raptar / Mars / radius / etc
A hand hold ?
I fell like 1% of ppl with them actually have a raptar / Mars / radius / etc
I use it to mount my Garmin Xero chronograph using the grayops mount
Garmin or Vortex Impact 4K because RAPTAR/MARS are for rich people.
I use mine mostly as a hand-hold. Even though I don't run my support-hand on it when shooting like some guys do, IMO it's still nice to have a spot I feel less bad about mashing down on (rather than using the scope bell) when mashing/sawing the rifle into a bag when building a position (especially on the clock).
I also used to use the rail to mount a red dot, which for me was sort of "training wheels" used to help get better with target acquisition (I no longer need/use a dot, ditched it in favor of more hand-hold/mashing real estate).
Plus/besides, if I ever really need one, like if zombies ever come, I'll already be GTG for a rail-mount LRF...
Those of you running the A419 mount, how are you liking it?* Return to zero when removed/replaced and torqued?
*[Besides the rail issue that was discussed earlier]
I’m lookin to snag a ZCO in the next week or two and figured I’d give them a try. Been running NF and BO on personal rifles since 2008 and was planning on going BO again…until I noticed the A419.
They make good stuff so I figured why not.
*[Besides the rail issue that was discussed earlier]
I’m lookin to snag a ZCO in the next week or two and figured I’d give them a try. Been running NF and BO on personal rifles since 2008 and was planning on going BO again…until I noticed the A419.
They make good stuff so I figured why not.
another to consider is the ZCO block mount.
I was using one on my S&B but decided to go with Hawkins rings for lower height. I like it a lot and the rail issue it resolved by buying the new short rail.
I just purchased another one in 36mm for a ZCO as well. Should be here next week and can give you some feedback then.
The Area 419 doesn’t do anything better than the BO C1 but it is cheaper after accessorizing so I would go 419 all day. The ZCO block mount although it’s a nice mount it’s too expensive imo.
Would definitely use the ZCO mount, all my ZCOs get the ZCO mount!
You need a tactical cap! I love Near’s mounts, alas I have two for sale with said cap.
Last edited:
Is that this thing? The cap in the back (I sound like Dr. Seuss).
Richard is def not the most awesome web designer of all time. But I still wish he was my dad.
Both my mounts are just not quite tall enough to put caps on. Just what happens when you order them for rifles with sporter barrels.
Just now seeing the auto correct of sporter to shorter.
Attachments
Similar threads
