AR Positional POI Shift Test

#51
357Max said:
I've got 40 rounds loaded for the test. 6ARC
Lapua Grendel necked down
108 eldm
29.4 Lever
2.290 oal
should be 2670-2700 This barrel only has about 40 rounds on it. It is the replacement Rainier UM. If head space grows over these 50 rounds they can stick this barrel up their ass.

VLTOR Fusion F-15 Face trued & shimmed. The VTOR Fusion extension is just as loose as the MUR's
Steel KRG Arca rail
22" +2" gas barrel
Gun weight with Ckyepod & no mag is 15lbs-6oz.

I'm thinking 5 rounds to get a good zero @100y Bi-pod/rear bag & light preload, 5 more to true dope to waterline at 500y with same bi-pod rear bag. Then build and break position 5 x with 3 shots each from prone bipod/rear bag to kneeling off a barricade with a smedium heavy fill up against the magwell.

Does this sound like a reasonable test?
What is the preferred program you guys would suggest I use to calculate mean radius after this test??

500Y on paper will probably hurt my feelings. Hopefully the load will be at or under 1 moa at 100y

Thanks
Click to expand...
Test sounds good. I am with @PBWalsh on shooting at 100y. External factors can skew the data at distance. Converting the measurements to MOA/MIL after verifying on paper over multiple groups is what I recommend. Try and shoot them how you normally would from bipod and barricade as to not skew data. If you normally load bipod then do that, however as an instructor I would recommend trying a more neutral position in the future ;)

Hornady 4Dof and BallisticX are what I use for measuring groups. I typically go with Ballistic X as it's only function is to measure so it's quicker to knock out and more refined in my experience.
 
  • Like
Reactions: Jsp556 and 357Max
#52
357Max said:
The gun still has a gap between the magwell & the rail. For the poi shift flex must be happening across the joint where the extension mates to the upper. Seems like the steel rail may actually aggravate the issue since it's heavy. In addition to the heavy Arca, I've got a few weights out towards the front of the rail.
View attachment 8442357



The range I'll be shooting at for this has 100 & 500 only.
I could just shoot dots @100y, but I'd still want to enter them all into some program to calculate mean radius from dot center for the total group of 15 per position. Not sure what tool/program is best suited to do that?
Click to expand...

Your thinking is correct. I've tested positional vertical shift with my LAM through my day scope on a wall at dusk at 200 yards and the shift is greater (.2 mil more) when I have a bipod hanging on the end of the rail.
 
  • Like
Reactions: PBWalsh and 357Max
#53
I shot for shift today.

3 rounds prone - 3 rounds bagged tight to magwell x 5 cycles
On the last round prone I shot 1 at small dot upper left, same for bagged, but I dialed U.3 & L.2mil.

There is definite shift, but I certainly had a bit of wobble of the bag. Grip is definitely different between the 2 positions as well. How much if any that contributes I don't know.
This was just a load I picked, not worked up. Shot decent about 1" for 5. I was switching between this test, a 6.5PRC, & a 16" 308 AR letting them cool. It was 96 degrees. 50 rounds each so I was a bit fatigued by the end.

Left the Garmin setup at prone so it picked up all 15 prone + 4 from the bag. SD pretty good for Virgin brass & Lever.

1719196413626.jpeg

1719197231275.jpeg



1719197100113.jpeg

1719197285072.jpeg
 
  • Like
Reactions: bfoosh006, Jsp556, PBWalsh and 2 others
#54
357Max said:
I shot for shift today.

3 rounds prone - 3 rounds bagged tight to magwell x 5 cycles
On the last round prone I shot 1 at small dot upper left, same for bagged, but I dialed U.3 & L.2mil.

There is definite shift, but I certainly had a bit of wobble of the bag. Grip is definitely different between the 2 positions as well. How much if any that contributes I don't know.
This was just a load I picked, not worked up. Shot decent about 1" for 5. I was switching between this test, a 6.5PRC, & a 16" 308 AR letting them cool. It was 96 degrees. 50 rounds each so I was a bit fatigued by the end.

Left the Garmin setup at prone so it picked up all 15 prone + 4 from the bag. SD pretty good for Virgin brass & Lever.

View attachment 8445213
View attachment 8445219


View attachment 8445217
View attachment 8445220
Click to expand...
Appreciate the data. Nice work building in the reps of a drill while also doing some testing and load dev.

As far as stability. Kneeling or sitting? If kneeling, double knee down or strong side knee up?

Also, for anyone interested I added the link to my targets. Broken down into .1 mil grids (at 100y) with measurement reference for group measuring apps.
 
#55
357Max said:
I shot for shift today.

3 rounds prone - 3 rounds bagged tight to magwell x 5 cycles
On the last round prone I shot 1 at small dot upper left, same for bagged, but I dialed U.3 & L.2mil.

There is definite shift, but I certainly had a bit of wobble of the bag. Grip is definitely different between the 2 positions as well. How much if any that contributes I don't know.
This was just a load I picked, not worked up. Shot decent about 1" for 5. I was switching between this test, a 6.5PRC, & a 16" 308 AR letting them cool. It was 96 degrees. 50 rounds each so I was a bit fatigued by the end.

Left the Garmin setup at prone so it picked up all 15 prone + 4 from the bag. SD pretty good for Virgin brass & Lever.

View attachment 8445213
View attachment 8445219


View attachment 8445217
View attachment 8445220
Click to expand...
I'd be curious about the loads generated if you moved the sandbag leftward and put the handguard into the L shaped part of the barricade. Bag below, barricade upright stabilizing from Left. Not snugged up to the magwell for depth on the port. More adjacent support, standing position, using that L shape in the barricade. The further out along the handguard's length, the more likely you get diversion. If it's going to flex.
 
#56
flogxal said:
I'd be curious about the loads generated if you moved the sandbag leftward and put the handguard into the L shaped part of the barricade. Bag below, barricade upright stabilizing from Left. Not snugged up to the magwell for depth on the port. More adjacent support, standing position, using that L shape in the barricade. The further out along the handguard's length, the more likely you get diversion. If it's going to flex.
Click to expand...
Thats not how I normally place the bag. Typically kI’d place it long side under rail with the crease up, that is a little more stable. For this test I wanted to see how well the VLTOR monorail resisted shift.
Maybe next time I’ll shoot it normal and see if shift improves any.
On something like a cattle gate the gun is up to the madwell as I tested though.
 
  • Like
Reactions: Veracity and flogxal
#57
Any chance you have access to a JP SCI-20 to test and see how it does with POI shift? Very curious to how that one would perform compared to the RD15
 
  • Like
Reactions: cbn
#61
Initial range session with a new Aero M4E1 upper with their enhanced handguard and a Blackstone Arms 12.5" barrel shooting AAC 77 OTM. Velocity averaged 2634 with a 16.1 SD. Group shown in the top right is ~.56". Extremely impressed with the upper's performance.

POI shift is now only .2mil and I am very ok with that small of a shift. Looking forward to seeing this barrel develop as the round count increases. Thats half of the shift I experienced with the Vltor/WOA upper. .2mil is within most targets I'll be shooting, and .2mil is easier to add to my data than .4mil.

IMG_20240711_142242_629.jpg
IMG_20240711_142242_659.jpg
 
  • Like
Reactions: Jsp556
#62
j-moose32 said:
Tagging @Veracity back in to see if he’s ever put a JP SCI -20 on paper like this
Click to expand...

I have a couple JP SCI-20 that I can perform the above test on. Don't know when I'll be able to get it done but I'd be happy to contribute.

I have two barrel choices for the SCI-20, one in 20" and the other is 22". The SCI-20 Upper is extremely rigid and all barrels are a mandatory thermo fit.

22" CLE Kreiger, CLE Match Chamber, 1-7.7 Twist, Rifle Gas, M110 Contour.

20" Craddock Chrome Moly Bartlein with CLE Match Chamber 1-7.7 Twist, Rifle Gas, M110 Contour.
 
Last edited:
  • Like
Reactions: Jsp556, bfoosh006, LRRPF52 and 3 others
#65
Veracity said:
Yes. That’s how semi-monolithic are designed. LaRue, Aero Enhanced, Seekins, Ridgeline, Mega all have models with similar setups. The added receiver thickness helps as well.

I’ll try and mount an LA5 this week and see what I can do for rail deflection. I’ve never seen a rail that did not have some movement so I doubt we will ever get to 0, but some have flexed less than others. The most rigid I’ve seen so far is the SOLGW M89/L89 rails.
Click to expand...
Do you have access to a L89 Broadsword upper to perform this same test on?
Thanks
 
#66
j-moose32 said:
Tagging @Veracity back in to see if he’s ever put a JP SCI -20 on paper like this
Click to expand...
Sorry for the hiatus.

Yes I have but only a limited sample. I saw no discernible POI shift. That said I have others say they see about .1MIL.

We all put pressure on guns a little different so take that with a grain of salt.
 
  • Like
Reactions: PBWalsh and j-moose32
#67
Veracity said:
Sorry for the hiatus.

Yes I have but only a limited sample. I saw no discernible POI shift. That said I have others say they see about .1MIL.

We all put pressure on guns a little different so take that with a grain of salt.
Click to expand...
Thank you. So the JP performs as good or better than the RD15 (and I expect it to considering the price point of JP)
 
#69
j-moose32 said:
Thank you. So the JP performs as good or better than the RD15 (and I expect it to considering the price point of JP)
Click to expand...
The JP is a solid choice.

You can make about anything have a POI shift with enough force. Doing the testing and putting in the reps to build consistency in fundamentals will aid as much as a new rifle that has no/little shift.
 
  • Like
Reactions: PBWalsh and j-moose32
#70
jackinfl said:
@Veracity Sir, did you get a chance to document your Seekins Precision uppers? Curious if the IRMT-R upper exhibits the shift.
Click to expand...
I’ve got a bit of data on them with the average being around .05-.1 MIL with how I shoot them. That’s both large and small frame. The only one I have yet to test is my SP-10M 6 Creed upper.

I’ve been traveling and busy with Army retirement I’ve neglected range time with the AR’s the past few weeks so I apologize for not updating more often.

I’ll get back to more testing as I have a few new uppers/rifles I have been sent to test. I also plan to test various carrier designs and folding adaptors to see if they affect precision.

Edit: Here is a pic I had accessible of prone with bipod then from just a gamechanger below it. (20" 224 Valkyrie)
566A21AD-9722-4D64-9545-D0584B536CE4_1_105_c.jpeg
 
Last edited:
#72
Personal data point. last week I took the 5 day Full Sprectrum SPR class at Ridgeline. I learned that my rifle has a ,4mil positional shift low when comparing prone with bipod and rear bag to standing off of a solid barricade with a bag.

My rifle is a BCM Keymod rail with a sawtooth rifles arca rail attached. I have a 18" Bartlein spun up by Craddock Precision with the Allen Engineering AEM5 can.

The facility and instruction at Ridgeline were all FANTASTIC. The instructors demoed everything at exceptional speed and precision with their new Ridgeline LPR rifle. 3 of the 11 students shot the Ridgeline gun. I student bought an upper and one bought a complete rifle during class. Having said that, at no point did the instructors make the class a sales pitch to buy their rifle. I was impressed by this.

My fix for my shift was to just add half of the correction, so .2 up to any of my dope. It seemed to work fine for me. My other thought was to
zero from the standing barricade.

I will defer to @Veracity and his opinion on rather or not that is a fix recommended to others.

I definitely had vertical stringing in prone, as I was trying the Ridgeline, "1 bag to rule them all" philosophy. I am not used to using the game changer in prone and it shows. The shmedium game changer with the heavy fill, on their barricade was super stable for me.

Anyway, I hope this information proves helpful.

Photos show Prone on Left, Barricade on Right then 10 shot barricade group on photo 1. Photo 2 is close up of prone. Photo 3 is close up of barricade. Photo 4 is Rifle on their barricade.
Prone and barricade B8.jpg
Prone close up.jpg
Barricade close up.jpg
Rifle on Barricade.jpg
 
  • Like
Reactions: Jsp556, LRRPF52, Rudy Gonsior and 1 other person
#73
AXMC said:
Since you mentioned a SOLGW m89/l89 upper...any data on them?
Thanks
Click to expand...
Just finished a large frame build with a SOLGW M89HA 16.75" rail. Really liking the rail, it's stout. Will test this for shift in the next couple weeks. This has a titanium barrel nut. Upper is a B-Kings Mod - 0 ( -.004" extension bore).
18" 6.5 Creed, 7.5T, RL + 2" gas.

Receiver face trued & drilled for SOLGW dowel pin. Barrel bedded with 620
1724030995947.jpeg



1724030189884.jpeg
 
Last edited:
  • Like
  • Love
Reactions: bfoosh006, Jsp556, jackinfl and 1 other person
#75
AXMC said:
Since you mentioned a SOLGW m89/l89 upper...any data on them?
Thanks
Click to expand...
I no longer have the M89 drive lock 6max and couldn’t find pics when I tested it. But here is one I did today when I mounted a new scope of my M76 broadsword.

IMG_9023.jpeg
 

Attachments

  • IMG_9021.jpeg
    IMG_9021.jpeg
    780.5 KB · Views: 34
  • IMG_9018.jpeg
    IMG_9018.jpeg
    742.6 KB · Views: 31
  • IMG_9020.jpeg
    IMG_9020.jpeg
    719 KB · Views: 34
  • Like
Reactions: BuildingConceptsllc, Jsp556 and MxTexas
#76
Thank you! You don't happen to remember if it did any better? I'd assume the drive lock instead of wedgelock and non-rotation lugs might provide a slight bit of improvement, but not hugely so, right?
Thanks
 
#77
AXMC said:
Thank you! You don't happen to remember if it did any better? I'd assume the drive lock instead of wedgelock and non-rotation lugs might provide a slight bit of improvement, but not hugely so, right?
Thanks
Click to expand...
I recall it being in the .15 mil range but I just don’t remember exactly. That was with a 20” and no suppressor.

The drive lock has appeared to help from what I’ve seen on a few students guns. I wish I had more data for you on it.
 
#78
Veracity said:
I recall it being in the .15 mil range but I just don’t remember exactly. That was with a 20” and no suppressor.

The drive lock has appeared to help from what I’ve seen on a few students guns. I wish I had more data for you on it.
Click to expand...
Thanks, I appreciate it!
As far as the Broadsword lower, do you like the grip being moved back in relation to the trigger? Do you think it helps you with trigger control?
Thanks
 
#79
AXMC said:
Thanks, I appreciate it!
As far as the Broadsword lower, do you like the grip being moved back in relation to the trigger? Do you think it helps you with trigger control?
Thanks
Click to expand...
I do. Having shot a lot of others rifles with adjustable grips to dial in finger placement I prefer it being farther back. For my hand it’s almost perfect with the TLC grip.
 
  • Like
Reactions: Jsp556 and AXMC
#81
Veracity said:
I no longer have the M89 drive lock 6max and couldn’t find pics when I tested it. But here is one I did today when I mounted a new scope of my M76 broadsword.

View attachment 8485560
Click to expand...
Did you change anything else besides the scope? If this is the same upper used in the initial test, not only does it seem to prefer AAC OTM's to the Black Hills, but the shift seems to have lessened .1 to .2mil as well.....
Thanks
 
#83
AXMC said:
Did you change anything else besides the scope? If this is the same upper used in the initial test, not only does it seem to prefer AAC OTM's to the Black Hills, but the shift seems to have lessened .1 to .2mil as well.....
Thanks
Click to expand...
I changed to a much lighter can that is using a 419 adaptor instead of a heavy brake
 
  • Like
Reactions: Jsp556 and AXMC
#84
Well This SOB shoots damn good. Only have 50 rounds on it just shaking it out. Will be getting a shift test in the next couple weeks for sure.
Just might shoot this at the Major Land match in Oct.
1725412430362.jpeg


Factory load of Prime 130 (smk I think). 2617 SD 16.6

1725412528849.jpeg


First attempt hand load Berger 130 otm pet bolt gun load backed off .8gr
One and done. 2740 SD 7.4
1725412730472.jpeg
 
  • Wow
  • Like
Reactions: LRRPF52 and Veracity
#85
357Max said:
Well This SOB shoots damn good. Only have 50 rounds on it just shaking it out. Will be getting a shift test in the next couple weeks for sure.
Just might shoot this at the Major Land match in Oct.
View attachment 8494081

Factory load of Prime 130 (smk I think). 2617 SD 16.6

View attachment 8494089

First attempt hand load Berger 130 otm pet bolt gun load backed off .8gr
One and done. 2740 SD 7.4
View attachment 8494093
Click to expand...
Very very nice!!! Love the KGM can to top it off!
 
#87
357Max said:
Well This SOB shoots damn good. Only have 50 rounds on it just shaking it out. Will be getting a shift test in the next couple weeks for sure.
Just might shoot this at the Major Land match in Oct.
View attachment 8494081

Factory load of Prime 130 (smk I think). 2617 SD 16.6

View attachment 8494089

First attempt hand load Berger 130 otm pet bolt gun load backed off .8gr
One and done. 2740 SD 7.4
View attachment 8494093
Click to expand...
You’re running an SCS in that I assume....

I really think 130gr is where it’s at in .260 Rem and 6.5CM gas guns.

My .260 Rem with Berger 130s has been a laser for me, though I don’t shoot it anymore.

The boy has been asking about it, so that will get me to take it out sometime when I get around to it.
 
#88
JohnDeereGuy1996 said:


I found this video interesting. He pretty much claims they didn’t solve poi shift issues
Click to expand...

Reading the comments, someone said something about the lower not being ambi because of a patent minefield on ambi bolt catches for ARs. The reviewer stated disappointment in not getting ambi features in an AR-15 in that price range, since the ambi bolt release is very useful in position shooting in matches when on the clock.

I just read through and analyzed the patent diagrams for all the listed ambi bolt catches and didn’t see too much there.

US20100275485A1 *2009-04-302010-11-04 Smith & Wesson Corp. Ambidextrous bolt stop
US20160069628A1 *2012-10-112016-03-10 Heckler & Koch Gmbh. Magazine release apparatus and firearms including such magazine release apparatus
US20210222971A1 *2020-01-212021-07-22 Polaris Capital Llc Bolt catch for firearm
Family To Family Citations
US6634274B12000-12-112003-10-21 Geoffrey Andrew Herring Firearm upper receiver assembly with ammunition belt feeding capability
US7661219B12007-01-102010-02-16 Knights Armament Company. Ambidextrous bolt catch for firearms
US8161861B22009-04-012012-04-24 Magpul Industries Corp. Battery assist device
US8327749B22009-09-102012-12-11 Underwood Joshua A Firearm receiver with ambidextrous functionality
US9291412B1 *2010-03-222016-03-22 Phase 5 Weapon Systems Inc. Monolithic extended bolt release (EBR) devices and methods
US8695477B2 *2010-05-242014-04-15 Tactical Link, Inc. Bolt catch-release lever
US9494378B22010-10-082016-11-15 Lwrc International Llc Ambidextrously operated bolt catch assembly
US8359966B12011-10-212013-01-29 Brotherton William A Ambidextrous rifle bolt stop release
US8978282B2 *2012-08-212015-03-17 Robert Hudson Garrett Lever for ambidextrous magazine releases for firearms
DE102012019422B32012-10-022014-04-03 Heckler & Koch Gmbh Lock catch for a firearm and with this designed handle and weapon housing of a firearm
US9417020B22014-01-102016-08-16 Falkor Sid, Inc.Ambidextrous bolt catch and magazine release and firearm
US9651328B12015-01-062017-05-16 Paul A. Oglesby Ambidextrous bolt release for a lower receiver
US20170241729A1 *2016-02-232017-08-24J & K Ip Assets, LlcBolt Catch for a Rifle

There are several knock-offs of the Magpul BAD, which I’m not a particular fan of. If they work, they’re great, but the mass can induce unwanted bolt hold-opens in some ARs.

One of the biggest issues people encounter, especially when running aluminum GI mags, is that some of the ambi designs out there won’t hold on last round, or rotational inertia on lightweight ARs will inadvertently activate the hold open future when you’re still shooting.

The ADM ambi design avoids this by separating the right side lever from the main bolt catch, separating the masses.

My SilcencerCo Ambi lower has what basically is a PDQ lever. Some have said they had GI mags not initiate LRHO with them.
 
#89
JohnDeereGuy1996 said:


I found this video interesting. He pretty much claims they didn’t solve poi shift issues
Click to expand...

I watched that as well. I’ve shot 4 different RD-15’s and have not noticed the issues that he had. It is hard to say without seeing what someone else sees when shooting to know 100% what’s going on. But he has some valid opinions.
 
#91
AXMC said:
Any anodizing issues on the ones you have/have shot?
Click to expand...
Not that I’ve seen. I’m not sure how the batches are done or if they have changed who does it.

I have 1500 rounds on mine and used bipod in various position with no abnormal wear.
 

Attachments

  • IMG_9193.jpeg
    IMG_9193.jpeg
    385.2 KB · Views: 18
  • IMG_9194.jpeg
    IMG_9194.jpeg
    378.5 KB · Views: 19
  • Like
Reactions: Tx_Aggie and AXMC
#92
Veracity said:
Not that I’ve seen. I’m not sure how the batches are done or if they have changed who does it.

I have 1500 rounds on mine and used bipod in various position with no abnormal wear.
Click to expand...
Did you get a chance to retest the seekins imrt? How would you say it compares to the ridge line system. If it’s on par I’d say the seekins dmr is a good buy.
 
#93
This is a great thread. In my experience there is going to be a POI shift based on the position of the shooter that varies from a prone zero. This is especially evident with gas guns. How we hold the gun and manage the recoil is going to be different in each position.

At work we do what is called a Variable Height Grouping Drill where we build a shooting position every 7” and shoot a 5 round group. So you’ll shoot at 7”,14”,21”28” etc. This shows two things, whether you have a consistent POI shift, and where your marksmanship fundamentals are at in different positions.

A man far smarter than I explained that when he was deploying to an urban environment, he would zero standing supported off a tripod because that was the position he utilized the most in that terrain. When he deployed to a rural mountainous environment he would zero prone for the same reason.
 
You must log in or register to reply here.

Similar threads

PBWalsh
Accessories Vltor/WOA/BRT Upper
Replies
2
Views
132
PBWalsh
PBWalsh
H
12.5 criterion and garmin velocity dump
Replies
28
Views
754
NHR
N
AR-180
AI Barrel Change POI Shift and Suppressor POI Shift
Replies
0
Views
410
AR-180
AR-180
B
POI change from bipod to barricade
Replies
39
Views
2K
Rio Precision Gunworks
Rio Precision Gunworks
RackSqueezeBang
Trouble Shoot Sudden POI Drop
Replies
10
Views
338
Slides
Slides
Top Bottom
Back
Home
Forums
Merch
Alerts