• Get 30% off the first 3 months with code HIDE30

    Offer valid until 9/23! If you have an annual subscription on Sniper's Hide, subscribe below and you'll be refunded the difference.

    Subscribe

  • Having trouble using the site?

    Contact support

Search results

Search the forum Search Articles
  1. G

    Bolt Extraction problems for Remington 700P, any advice?

    I plan to lower the charge, see if the problem persists. From what people on here have told me, it seems my handloads are showing pressure signs, ie. flat primers. Hopefully lowering the charge and using a different scale to measure my powder, might lead to some good results. I'll look into...
  2. G

    Bolt Extraction problems for Remington 700P, any advice?

    Alright, will do. I'll try it out, next time I can head out to the range.
  3. G

    Bolt Extraction problems for Remington 700P, any advice?

    Was using an RCBS ChargeMaster 1500 Digital Scale, zeroed out with the calibration check weights
  4. G

    Bolt Extraction problems for Remington 700P, any advice?

    Bullet & weight: 175 grain sierra match kings Powder & charge IMR 4064 ranging from 41 - 42.5 gr (.3 increments) Case: IMI 308 Win Match, Lake City LR 07 Case length: 2.005" Cartridge length: 2.800-2.801 Primer: Winchester Rifle Primer depth: .01 from flush Minimum & maximum times...
  5. G

    Bolt Extraction problems for Remington 700P, any advice?

    Thanks for the suggestion, I will look into that.
  6. G

    Bolt Extraction problems for Remington 700P, any advice?

    I will try to get all the details for you by tomorrow. My friend was the one that helped me load these rounds. He said he'll come by and help me. I'll have all the measurements and I'll try to take some pictures of the cases also. As for separation, of cases I have been trying to pick out the...
  7. G

    Bolt Extraction problems for Remington 700P, any advice?

    Yes, I have tried cleaning it, and wiping it down dry. Unfortunately same results. Same with leaving a light coating of lubrication in the chamber as well. What makes this so confusing is it doesn't happen every single time. It's maybe 1 out of every 5 that this happens, and sometimes the...
  8. G

    Bolt Extraction problems for Remington 700P, any advice?

    After going to the range yesterday, I'm still confused as to what is wrong with either my rifle or my handloads. I shot some factory ammo, but encountered no major problems. The brass seemed to eject without issue, except for 1 or 2 of the 20 rounds fired, that had slight resistance when...
  9. G

    Bolt Extraction problems for Remington 700P, any advice?

    The IMI cases were also brand new never fired brass from the factory. Never sized, so they should have been in spec. As for the trigger, I thought it also was the 40x trigger, but when I checked my serial number through Remington's website it said that my rifle was affected by the trigger...
  10. G

    Bolt Extraction problems for Remington 700P, any advice?

    Actually, now that you mention it, I have noticed similar gouging marks in some of my brass. I'll try to get some pictures when I get home later. Not quite as obvious as from your pictures but it is there on a few of the cases. Hopefully I can get to the range again soon, I plan to try testing...
  11. G

    Bolt Extraction problems for Remington 700P, any advice?

    I recently purchased a brand new Remington 700P, in 308. After >100 shots I began having issues with the bolt extracting properly. The bolt would remain stuck in the chamber and wouldn't slide out to eject the spent brass. I tried to see if perhaps it was just that round, but have continued...
Top Bottom
Back
Home
Forums
Merch
Alerts