Search results
-
7mm short magnums.
Betting the 166atip is going to be fun in the 7-6.5prc- Geno C.
- Post #49
- Forum: The Armory
-
-
7mm short magnums.
The wsm isn’t going anywhere. The 300wsm is one of the most shot rounds in long range benchrest.- Geno C.
- Post #42
- Forum: The Armory
-
7mm short magnums.
I mean not the most use out of a short action 7mm😏 a Norma shorted and necked down is about the most use- Geno C.
- Post #40
- Forum: The Armory
-
7mm short magnums.
I’m not salty at all. If I had a long action, I should wouldn’t neuter it with a small case. The only way a wsm makes sense is a short action. The 7wsm makes the most use out of a short action 7mm. Long action, there are so many better cases out there. The new thought that you have to have all...- Geno C.
- Post #39
- Forum: The Armory
-
7mm short magnums.
Shooting a 7wsm in a long action is some monkey pox shit. Why shoot a short action case in a long action instead of a long action case ?- Geno C.
- Post #37
- Forum: The Armory
-
7mm short magnums.
Must have missed where my necks are turned because of a tight neck chamber- Geno C.
- Post #28
- Forum: The Armory
-
7mm short magnums.
You can be seated past the donut and it has no effect on target if the chamber neck is large enough to allow a clean release- Geno C.
- Post #27
- Forum: The Armory
-
7mm short magnums.
Still wrong. A donut that isn’t restricted by chamber neck diameter and is allowed to fully release the bullet isn’t a problem at all.- Geno C.
- Post #26
- Forum: The Armory
-
7mm short magnums.
If there’s clearance and you’re not seating below the donut, then it’s like it’s not even there- Geno C.
- Post #22
- Forum: The Armory
-
7mm short magnums.
That would be silly considering you wouldn’t get the bolt closed- Geno C.
- Post #21
- Forum: The Armory
-
-
-
7mm short magnums.
I’m only turning necks because I got a reamer that needed it. I would spec .320” neck diameter and a .535 base if I were to design the reamer- Geno C.
- Post #12
- Forum: The Armory
-
-
.375 Raptor Recipe
This is sort of where I’m headed. Can anyone post a pic of their raptor like this? L to R 400gr lazer, 390gr sicbm2, 390 atip- Geno C.
- Post #57
- Forum: Reloading Depot
-
7mm short magnums.
180 in a 7-6.5prc loaded to 2.950. Just shy of 2800 from a 22” barrel- Geno C.
- Post #7
- Forum: The Armory
-
416 Stroker/Snipetac
They are basically the same thing. One is no better than the other.- Geno C.
- Post #2
- Forum: ELR - Beyond 1000 Yards
-
390 grain Hornady A-Tip load development 375 Cheytac
2950 in an 8 and they’re holding together- Geno C.
- Post #340
- Forum: ELR - Beyond 1000 Yards
-
Gunsmithing 1/2x28 for .243/6mm???
If your cans are already 9/16 I’d stick with that. 1/2 won’t hurt anything. Mike from tac ops threads his stuff 9/16 fwiw- Geno C.
- Post #9
- Forum: The Armory
