Search results

Search the forum Search Articles
  1. cannoncrossfire

    Tikka T1X

    My mistake, looks like the front pin is holding the section of firing pin. I tried punching the pin out but it didn't budge. Might need heat if its loctited or something to stop it from sliding out and becoming a problem. If something has broken though id be chasing down Beretta to replace it...
  2. cannoncrossfire

    Tikka T1X

    @Redshako I was going to make a video how to do it for replacing the bolt shroud. Punch the pin out from the shroud, make sure you hold onto the shroud when you remove the punch because there's a lot of spring tension pushing backwards. You can use a pin punch or even a small enough allen key...
  3. cannoncrossfire

    Tikka T1X

    That's a pain... can you show a photo how/where it broke? Hope you get sorted out and back in business.
  4. cannoncrossfire

    Tikka T1X

    @Eoddave27 haha well you're more on the ball than I am!
  5. cannoncrossfire

    Tikka T3 Thread

    @WVHick that is a sweet rifle you've put together. What stock is that and what maker of the barrel?
  6. cannoncrossfire

    Tikka T1X

    The Sterk T1x parts have only juuuuust been officially announced, allow a bit of time for Eurooptic and Tacticalworks to have them listed. The T1x parts are not the same as the T3 parts though, the T1x swept ball handle had to be a completely new design - just uses the same knob on the end. The...
  7. cannoncrossfire

    CZ 457

    Oh awesome, they really did make a lot of improvements with the trigger guard and the knob/handle then. Im keen to get a look at the cz457
  8. cannoncrossfire

    CZ 457

    @POGPride nice build, so is the 457 factory handle pre-threaded? Whats the story there?
  9. cannoncrossfire

    Tikka T1X

    Watch the bolt stop as you pull the bolt back and forward... that might be the dragging youre experiencing? Otherwise a good clean and oil might improve it. It's not common for tikka/sako to leave any rough machining but it's possible. Theres a few cross pins in the bolt too which need to be...
  10. cannoncrossfire

    Tikka T1X

    Looks good, can you please take a pic of the inside backbone and trigger guard? Id love to see how its all attached with room for the mag well.
  11. cannoncrossfire

    Tikka T3 Thread

    You are 100% correct that the Tikka bolt bodies are not perfectly round. The dovetail cut out and cocking ramp are machined before heat treatment (easier on tools) so they heat up and cool slightly unevenly. Factory plastic shrouds will flex easily as well as t3x 'alloy' shrouds are super loose...
  12. cannoncrossfire

    Tikka T3 Thread

    I ship to individuals and distributors.
  13. cannoncrossfire

    Tikka T3 Thread

    @Travclem soo much love for that build, pure hotness
  14. cannoncrossfire

    Tikka T3/T3x - Ball Bolt Handle

    Thanks guys for the recommendation. Yes the next batch is creeping up, looking at doing some T1x parts as well as the usual T3 parts.
  15. cannoncrossfire

    Painting a Tikka stock

    Or just cure it real low and slow. A hot car gets hotter than the minimum temp to cure cerakote. Ive baked plastic oakley sunglasses with cerakote no problems.
  16. cannoncrossfire

    Tikka T3 Thread

    Beretta seems to let down the experience of owning a Tikka.
  17. cannoncrossfire

    Tikka T1X

    Removed the screw and pulled it off
  18. cannoncrossfire

    Tikka T1X

    there's an m5 screw in the t1x handle but you don't need to take it off to fit the plastic tikka knob. Unwind the screw to allow the plastic knob to come off - it has a plastic umbrella inside it that is opened when the screw is wound tight (gripping inside the metal tikka handle).
  19. cannoncrossfire

    Gunsmithing Cerakote Working Temperature Range

    I've blow torched cerakoted parts until they were cherry red. The Cerakote turns to a fine powder that you can wipe off. It still 'stains' the metal though so would still require blasting before new Cerakote application.
  20. cannoncrossfire

    FOUND - Stripped AT Chassis from Factory AIAT

    Would be interested to hear if there were many/any de-bonded chassis people were selling. PM if you're looking to sell.
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts