Search results

Search the forum Search Articles
  1. RandomWAguy

    Weighted bolt knob cz

    I am wondering if anyone here knows of a heavier bolt knob, I got one for my vudoo but would like one for my cz. The one I just got is about 5oz, the few that list weight are usually only around an oz. Ive already asked the vendor that makes the one I have and he is too small to make them for...
  2. RandomWAguy

    Bergara b14r carbon question

    I had one shortly and the cold bore flier was not consistent, so sold it after 3 range trips. Have 3 friends with steel and none have had the issues like carbon did.
  3. RandomWAguy

    Balancing Bergara B-14R in KRG X-Ray or MDT XRS

    Xray needs the enclosed arca forend and maybe three sets of weights, 480+310+135(3 sets snyder weights)=925 Xrs just needs the steel arca, 550+165=715 Neither is cheap by any means but nothing in this sport is. As others have said may want to see if you can stretch for a better base gun or set...
  4. RandomWAguy

    Balancing Bergara B-14R in KRG X-Ray or MDT XRS

    No issues with the weights on the forend, he got the steel one made for the manners and just used some mlok hardware to attach it.
  5. RandomWAguy

    Balancing Bergara B-14R in KRG X-Ray or MDT XRS

    Not a bergara but I have a Vudoo with 18" mtu and it needed the enclosed forend and two weight sets to balance. The new arca forend that KRG makes has a lot more mlok slots then the older version I have. Have a good friend with the XRS and bergara and he got a steel arca rail for it from 360...
  6. RandomWAguy

    Chassis for KIDD .22 RF

    Yes it is made to fit the kidd supergrade
  7. RandomWAguy

    B14R setup

    Pretty sure I saw somewhere he said it is the sawtooth rail for it
  8. RandomWAguy

    CZ 457 Clip On NV Rail/Stock Options?

    Could be wrong but pretty sure KRG has accessories for the bravo to use NV....
  9. RandomWAguy

    CZ 457

    From pics Ive seen the xrs already tapers into the magwell, so you really shouldnt need the magwell insert. The two you mention are made for chassis that have huge holes for the magwell, thats why they made those plastic inserts for them. If you mean the actual cz magwell disregard this.
  10. RandomWAguy

    CZ 457

    Too bad he has retired and shut down his site.
  11. RandomWAguy

    CZ 457

    If its anything like the Xray all he did was remove the bravo parts from the backbone and installed the whiskey front then trimmed the grip on the backend and installed the rear end.
  12. RandomWAguy

    CZ 457

    I'm curious how easy is it to reach the mag release with the new 13 rounder? Ive heard the ACC is pretty impossible to mag change with mag extensions...
  13. RandomWAguy

    CZ 457

    I am pretty sure that the xray back end is lighter than the bravo but I am not positive. Its not going to balance without some weights on the front of it, Ive get two sets on it and a different forend on it so I could use the weights. Handles pretty well but it would be heavy for sure as a...
  14. RandomWAguy

    CZ 457

    Was playing around with the krg bravo and figured I would try to switch to the xray rear. Took a little bit of trimming on the grip, very minimal, but it bolted right up.
  15. RandomWAguy

    Another cz mtr question

    Just ordered a mtr and am wondering if anyone has put the area 419 weighted arca on one? I already have a spare 14" non weighted that I can use but would be nice to get some more weight out front if possible.
  16. RandomWAguy

    EC Tuner

    How many rounds total do you have through the vudoo? Need to make sure the barrel has settled before trying to tune it.
  17. RandomWAguy

    Parallax setting for .22 competitions

    That was a fun match! It was by far the best run and laid out rimfire match I have been to. That was my first time going but will go back again, best part was I made the video. Actually best part was everyone doing their impression of Bob Lee from the boat.
  18. RandomWAguy

    Ruger Precision Rimfire

    Athlon midas tac, any of them
  19. RandomWAguy

    Introducing The Vision Chassis for R700, Tikka, Sako and Sig Actions

    Forgot to add that Rick is the man! Had some gremlins but everything was sorted out and he made a customer for life, thanks again!
  20. RandomWAguy

    Introducing The Vision Chassis for R700, Tikka, Sako and Sig Actions

Top Bottom
Back
Home
Forums
Merch
Alerts