Search results

Search the forum Search Articles
  1. J

    Pierced Primer Question: AI AX and Prime 107 Grain 6mm Creedmoor

    Here’s some pictures of the primers. I decapod the deep strike primers and one was fully pierced and the other two were slightly pierced
  2. J

    Pierced Primer Question: AI AX and Prime 107 Grain 6mm Creedmoor

    I need some help with trying to figure out what may be going on with my 2018 AI AX and factory Prime Ammo 6mm Creedmoor. Any advice or guidance would be appreciated: Background: 2018 AX with a 24" Proof stainless steel 6mm Creedmoor barrel (24") Factory Prime Ammunition 107 grain 6mm Creedmoor...
  3. J

    Vudoo V22 360 Trigger Install Questions

    I just installed a TT Diamond in my new 360 barreled action today. The pins were definitely a bit of a tight fit but went in just fine with a little patience and using both roll pin starters and slave pins to keep things lined up front and back. Having everything properly aligned makes it go a...
  4. J

    Vudoo Gun Works V-22 Rimfire Bolt Action

    Does anyone happen to have a picture of Vudoo with a 20" MTU that in a Bravo chassis with the enclosed forend? I'm trying to get an idea on how that configuration would look
  5. J

    Accuracy International Picture Thread

    That's a great point - what tape did you use?
  6. J

    Accuracy International Picture Thread

    That is really sweet looking! Great job!
  7. J

    Accuracy International Picture Thread

    Anyone have pictures of a rattle can paint job on an AT that they wouldn’t mind sharing? I’m thinking of spraying mine and would to see some of the patterns that you guys used
  8. J

    .260 Rem Resizing Question: RCBS Precision Mic and Hornady Compartor Giving Different Results

    writing #17 on a sticky note and putting it on the bench
  9. J

    .260 Rem Resizing Question: RCBS Precision Mic and Hornady Compartor Giving Different Results

    I get the point that you are making, so are you saying to go with what the RCBS mic is showing me?
  10. J

    .260 Rem Resizing Question: RCBS Precision Mic and Hornady Compartor Giving Different Results

    I'm in the process of getting some once fired .260 Lapua brass ready for reloading and I just noticed something odd that I need some advice on since I'm still a novice reloader... When I measure the headspace (on the deprimed and cleaned) brass with a RCBS precision mic tool, I'm seeing that...
  11. J

    Need some help with steel targets

    That’s a great point that I hadn’t even considered. I actually have some 3/8” plywood laying around in the garage that should work
  12. J

    Need some help with steel targets

    Thanks for all of links and suggestions. I think I know which direction to go in now for a solution
  13. J

    Need some help with steel targets

    unfortunately, I don’t have any experience with welding. I like how compact your design is
  14. J

    Need some help with steel targets

    those look great and portability is key for my situation. Who made the store bought model?
  15. J

    Need some help with steel targets

    I meant to add this picture to my original post but never noticed that the link didn’t display. It shows the issue that I’m having with the sandbags after about 40 rounds
  16. J

    Need some help with steel targets

    yeah - I swapped out my chains for the rubber strips awhile ago and it does help with reducing the swing. One this that didn’t occur to me just now is that I may need to spread out the two eye bolts on the 2x4 to help slow the swing a little more
  17. J

    Need some help with steel targets

    That would work. Who makes this one?
  18. J

    Need some help with steel targets

    I need some fresh ideas on how to address the following problem with my steel targets: The Problem: My target stand is constantly toppling over after 308 at 200 and 300 yards (range max distance) I’ve kind of run out of ideas on how to keep things upright so I’m hoping that someone has some...
  19. J

    Optics SOLD: NEW Schmidt Bender 5-20 Ultrashort

    Someone please buy this before I do. I’ve done several high end scope purchases with Scott and his stuff is always in excellent condition and he’s a great guy to deal with.
  20. J

    .260 Remington: Need Some Advice on an Starting Point for Load Development

    So, I landed at 42.5 grains of H4350 with the 136 Scenar as my “winner”, but now I’ve got a problem as I only have about 1/2 pound of that powder left so that’s not going to last much longer until I can find more of it. I do have a 5 lbs jug of RL17, so I’m thinking about starting the testing...
Top Bottom
Back
Home
Forums
Merch
Alerts