Search results

Search the forum Search Articles
  1. E

    Gunsmithing Bending tenacity bolt handle

    The boyds are made for the curved Remington handles .
  2. E

    Gunsmithing Bending tenacity bolt handle

    You will have to modifiy your stock for the new bolt shape. I was thinking about doing the same with some PTG bolt handles hope some guys here know how to to this.
  3. E

    Gunsmithing Need high quality 1/4” bits

    http://www.shooterstools.com/ I bought a torque wrench set from here and the bits are made in America and work great . We sell all the common brands at work Dewalt Milwaukee etc and none of them are as nice as the bits in the Borka set .
  4. E

    Gunsmithing Custom H&R barrels?

    Some shops around lower Mi were doing straight wall cartridge conversions now that they are legal for deer.
  5. E

    Gunsmithing What do you consider excessive headspace?

    I understand what you are saying no problem and have adjusted dies for chamber size . The OP asked about adjusting the chamber size to save brass and your right he can adjust his sizing die to resize cases so there's no stretch . I was talking about adjusting the chamber to some size other than...
  6. E

    Gunsmithing What do you consider excessive headspace?

    Your right that the brass can be sized to an short or longer chamber to a point but extremely short chamber may not allow factory ammo and a over size chamber cause the same issue with factory brass slamming into the bolt. You have to think about the next guy that ends up with the rifle not...
  7. E

    Gunsmithing What do you consider excessive headspace?

    I guess slamming the case back into the bolt would cause hard bolt lift and show pressure signs on the primers .
  8. E

    Gunsmithing What do you consider excessive headspace?

    Wouldn't excessive headspace make less pressure and more brass stretch ? I've always used scotch tape on the back of the go gauge to measure headspace but remember to peel it after measuring or you will be off on the next chamber job .
  9. E

    Mack Bro’s SS Evo

    Thanks
  10. E

    Mack Bro’s SS Evo

    Did they change the barrel shank dimensions for the newer EVO II's ?
  11. E

    Chambering blank for Tikka.

    When you say blank make sure its a profiled blank that will save you some time nd money . I see companies offer prefits for tikka rifles .
  12. E

    Gunsmithing Dual ejector springs on a factory Rem 700 bolt with a factory extractor

    We have to relieve some material above the extractors for rebated rims like the 450 like your saying but this cartridge rim slides over and catches the groove cut for the extractor . On a normal 223 bolt that area is all filled holding the cartridge into the extractor claw this setup lets the...
  13. E

    Gunsmithing Dual ejector springs on a factory Rem 700 bolt with a factory extractor

    We bought some of the actions PTG is selling this bolt also has the skeleton bolt handle they came with a RR serial number tube . I have a few factory 17 fireballs, 221 fireballs and the 300 blackout I don't think the spring is that far off the 223 plunger position .
  14. E

    Gunsmithing Dual ejector springs on a factory Rem 700 bolt with a factory extractor

    I'll get them up tonight meant to call you guys today crazy at work . The bolt on the left has the cut out for the extra spring I believe its right inline with the roll pin . The case pivots grabbing the extractor cutout on the opposite side . This one is a .350 but the .223's do the same so...
  15. E

    Gunsmithing Dual ejector springs on a factory Rem 700 bolt with a factory extractor

    We just shipped some bolts out today for fluting LRI does great work .
  16. E

    Gunsmithing Dual ejector springs on a factory Rem 700 bolt with a factory extractor

    Hello guys wondering if you guys have ran across this ? I bought some 223 Remington actions and the bolts have the relief cut for a second ejection plunger . Now that the action is barreled when cycled the brass gets hung up sticking in the bolt at a angle ? It seems to push the brass into the...
  17. E

    Gunsmithing Polishing a stainless barrel

    This is what I use to polish being a cheap skate I made everything but it would have been cheaper to buy time wise . You can correct some bad chatter marks with eighty grit and work your way finer all the way to chrome. Gordy uses a wire wheel to get that dull finish Shilen and Douglas barrels...
  18. E

    Gunsmithing What lathe for the home gunsmith?

    About six years ago I was struggling to find a decent lathe for barrel work . Most I looked at were badly worn in terrible shape or priced out of my price range . If anything was reasonably price it sold immediately with backup buyers waiting. A good friend that taught me how to run a lathe...
  19. E

    Gunsmithing Opening up bolt handle inlet on manners PRS1

    We open them up all the time with a sanding drum in a dremel tool . Does the inlet need moved or just bumped a small amount ?
  20. E

    Gunsmithing Looking for a rem 700 bolt knob jig and sako extractor jig

    I made a jig to hold the bolt in the mill and use a annular cutter to cut the shank before tapping .
Top Bottom
Back
Home
Forums
Merch
Alerts