Search results

Search the forum Search Articles
  1. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    Sold
  2. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    TTT
  3. R

    Accessories Spuhr 34mm mount Early GAP version similar to 4011. SOLD

    Price drop.
  4. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    Bipod is sold pending funds. Thanks
  5. R

    Accessories Spuhr 34mm mount Early GAP version similar to 4011. SOLD

    Is my price out of line? Make me an offer, trades considered.
  6. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    TTT
  7. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    TTT
  8. R

    Accessories Spuhr 34mm mount Early GAP version similar to 4011. SOLD

    TTT
  9. R

    Accessories Spuhr 34mm mount Early GAP version similar to 4011. SOLD

    I have an Early Spuhr mount that eventually became the 4011 34mm rings with 28mm height as requested by GAP as the story goes. Mount appears as new to me sat in safe on 6.5 creedmoor not really sure it was ever taken out to the range but it was mounted on a rifle. 300.00 275.00 last drop...
  10. R

    Accessories 6mm Hagar AR15 barrel and reloading stuff. Reduced

    I have a new unfired 6mm Hagar barrel by Criterion CBI 1:8 twist 20 1/2" total length. Was placed in upper but never fired. Heavy service rifle taper with front sight dovetails. Threaded 1/2 X 28. Barrel has matching headspace bolt. Measures just under inch under the handguards and 0.750 under...
  11. R

    Bottom metal installation CDI or PTG

    Thanks Guys just what i needed was information from people that use/install them.
  12. R

    Gunsmithing AMD 65 rear trunion crack

    Sorry for the delay. Thats what I'm worried about. My face is not the best looking around but i don't think it would be improved by a face full of ak bolt carrier either. I think i'll pull it out and see.
  13. R

    Bottom metal installation CDI or PTG

    I need to have DBM installed in a McMillan HTG stock. Both CDI and PTG offer inletting with purchase. Both seem to have a turn around time of 2-3 weeks. Any recommendations on with either one good or bad? Other suggestions welcome as well. Thanks Rad
  14. R

    Photo hosting site

    Thanks. I just need easy. Can you edit photos in Imgur. All i need is to resize them so they are not to large for web pages.
  15. R

    Photo hosting site

    I have used Photo Bucket begrudgingly for years. Since their new changes I need a different hosting site. Anyone have any suggestions? Free is great but i don't mind paying if its worth it. Looked at Cubeupload and SmugBug. Just not sure if anyone had any good experiences with anywhere...
  16. R

    Gunsmithing AMD 65 rear trunion crack

    I have an AMD 65 that I assembled years ago. Has about 500 rounds through it. I just replaced the wire stock with one with a cheek piece and noticed a crack across the rear of the rear trunion. It running from top left corner of the stock mortis to the left edge. I can't see it on the inside to...
  17. R

    Rifle Scopes Help with ID 2 sunshades with ARDs

    I have 2 what I think are USO sunshades with ARDS. The first is thread diameter of 1.990 in or 50.53 MM. The outside diameter of shade 2.229 in or 56.66 mm I assume this went to my USO 3-17 which I sold The second is thread diameter 2.278 in or 57.88 mm outside diameter 2.442 in or 62 MM...
  18. R

    1080P camera w/optical zoom for target camera: anyone using one?

    gasdoc09 any chance of some photos of your set up? I am especially interested in your power set up. I get everything except the power. BTW I am no way tech or electrical savvy but I manage to trial and error a lot of stuff together. I was looking at the Bullseye for 549 (doable) and the...
  19. R

    Gunsmithing Opinion on milling slot in feed ramp for longer OAL in Remington 700 type action.

    Yeah Ring that is the mod we are talking about. What caliber is your rifle in? jpretle. That has already been done to this receiver for the wyatt box in the HTG stock it was originally in. The problem is when you change to a DBM set up the magazine does not take advantage of the rear space so...
  20. R

    Gunsmithing Opinion on milling slot in feed ramp for longer OAL in Remington 700 type action.

    Thanks guys. I Have been thinking of doing this for a long time. Just wanted to see if anyone had done it with a WSM or SAUM. The set up is an AICS stock with accurate mags. The only reason I was even considering it is the exact same slot is cut in my Surgeon 591. What ticks me off is McFred...
Top Bottom
Back
Home
Forums
Merch
Alerts