Search results

Search the forum Search Articles
  1. CST

    ATX chassis screw torque value

    Thanks for the insight. The funny thing is the stock comes with stainless and when I removed em there is start of some damage to the hex. (After heatng it to loosen the loctite). That's why I'm asking about torque. The stainless cap screws are way too soft. If I had to fight the loctite anymore...
  2. CST

    ATX chassis screw torque value

    Thanks for the reply .however those 4 screws in the AICS chassis are M4 screws...
  3. CST

    ATX chassis screw torque value

    Accuracy Int. AT-x....Anyone know what the torque value needs to be on the 4 stainless screws(m4-.07) that holds the upper to the lower chassis.? See attached pic...the yellow arrows..thanks
  4. CST

    Accuracy International AT-X

    Does anyone know if AI sells low profile pic rails that will line up with the stock scope rail height....even the standard rails on a Remington 700 clone in the chassis's .
  5. CST

    AT-X CHASSIS and magazines

    Red Your the man! Thanks for for your wisdom...btw you mentions accurate mags...where do they fall under? ax or standard AICS type?
  6. CST

    AT-X CHASSIS and magazines

    Ok guys..I finally got it clarified from Mile High. The guy helping confirmed with the gunsmith. The ATX chassis needs the mags listed under AX chassis if u re look at the parts listing I posted above . The mags under AI legacy or AT AICS does not work. Here is a copy of the email. Hopefully...
  7. CST

    AT-X CHASSIS and magazines

    I'm just getting a little overwhelmed on all these part numbers Aics legacy AT Vs aX chassis...etc..
  8. CST

    AT-X CHASSIS and magazines

    Thanks...really appreciate it. The other mafs u have are all generic AICS mats? No AW or ATX Specific mags? AT, or AX?? Im very confused on the differences.
  9. CST

    AT-X CHASSIS and magazines

    Lone peak Fuzion. ..I took the action off and push it all the way up to the stop.....it engages the catch...but just too loose and will fall out if i shake it.
  10. CST

    AT-X CHASSIS and magazines

    Anyone know why the PMAG keeps falling out? I can't believe dimensionally that it would be that much smaller then a AI metal mag...front to back and side to side.. Would a AW may be better?
  11. CST

    AT-X CHASSIS and magazines

    I just bought a ATX chassis and bought a PMAG AICS magazine. The mag is too loose and undersized and readily falls out on its own. Could that be a chassis problem or just a pmag issue? .....or should I be ordering the AI AtX mags? Im so confused on which mag That chassis takes. Thanks.
  12. CST

    I Need prefit barrel education 6.5cm

    Lol....I talked to you last week and ordered the barrel from you already. Thanks for all the time and guidance on the phone. Eagerly waiting for the barrel! Thanks again
  13. CST

    Accuracy International AT-X

    Since people have had em for a while....So what do you all think of the keyslot design? I guess it's here to stay(even though they sell mlok handguards for the AXsr?forget which model).. What's different about it and key mod?
  14. CST

    Sphur vs AT-x chassis

    Lucky...I almost bought an impact
  15. CST

    Sphur vs AT-x chassis

    Using a lone peak fuzion...should be ok?
  16. CST

    Sphur vs AT-x chassis

    I assume the polymer MDT AICS would work?
  17. CST

    Sphur vs AT-x chassis

    Since it's a chassis for a Remington......am I limited to just ATX mags or would AICS,aw, PMAGS work?
  18. CST

    Sphur vs AT-x chassis

    What ring height are u using on that Sphur mount to clear the hand guard bridge/cover?
  19. CST

    Sphur vs AT-x chassis

    Since the AT-x chassis and Sphur sic has been out a while. Can you guys who own em, put some pics up and some feedback/positive and negatives....ive narrowed it down to these two stocks for my build.
  20. CST

    Lone peak Fuzion and chassis fit

    I just figured most chassis are designed for the rounded action of a Remington 700 compared to this style on the lone peak.. the milled flats would definitely provide an extra margin of bullet proof connection when bedding to a fiberglass stock.
Top Bottom
Back
Home
Forums
Merch
Alerts