Search results

Search the forum Search Articles
  1. P

    Reloading Equipment Ready to load RP .223 brass 1k pcs

    1x. It's from a private range no reloads.
  2. P

    Reloading Equipment Ready to load RP .223 brass 1k pcs

    Correct all RP (Remington) 223 brass
  3. P

    Reloading Equipment Ready to load RP .223 brass 1k pcs

    Sorry for the misunderstanding these aren't primed but fully prepped. Just prime and load.
  4. P

    Reloading Equipment Ready to load RP .223 brass 1k pcs

    I have 13 lbs 10 Oz of Fully processed RP brass for sale. 1.750 trim length, full length sized and stainless tumbled. Should be right at 1k pcs. Fully sorted all RP not a mix. $140 shipped.
  5. P

    Shyster Ammo Company? American Marksmen

    I've had good experiences with them but have just ordered brass so far. It was nicer than expected and had fast shipping. I do agree that the ammo mixup is concerning since I can see someone shooting 5.56 in a 300bo chamber.
  6. P

    Explain Your Resizing Process to Me

    My .02 is that PRS isn't benchrest but does have some aspect of hard use mud, sand, grit etc. I've had good luck full length sizing, bumping shoulder back .002 and then resizing with a mandrel to give .001-.002 neck tension. Redding full length sizing dies and Sinclair expander mandrel. You can...
  7. P

    Reloading Equipment Sealed 500 box of Berger 140 hybrids

    Don't really want to sell these but been spending more time with the AR's at the moment and could use a swap of inventory. Sealed box of 500, 140 hybrids. Bottom box in pic. $425 shipped obo
  8. P

    Advice on new AR-10, learning precision shooting

    Good call. It'll be easier and cheaper to start. A good barrel and trigger will take you a long way.
  9. P

    308 with accuracy/consistency issues

    It will be interesting to see how the barrel comes out after being bedded. My two uppers have all been thermal fit (heat upper/freeze barrel) but never dealt with any bedding or adhesive.
  10. P

    308 with accuracy/consistency issues

    If you got a handload with Berger's to go about an inch and the other standard loads are 1.5-2" then at this point I'm going to say that's all she's got capt'n. Friend at the club a few years back ended up wasting half a summer on a prefit barrel that was almost 1 moa. Ended up swapping it out...
  11. P

    308 with accuracy/consistency issues

    I've never had good luck shooting ar10's anything close to free recoil. Best is when I give a decent preload to the bipod, really focus on fundamentals and pretend to be a sack of dead meat behind the rifle when it goes off. Make sure you are holding the trigger all the way to the rear for the...
  12. P

    Reloading Equipment Processed 5.56 brass for sale

    Had lots of questions about this. Sorry for being confusing. I don't have it sorted by headstamp however. It's mostly 50/50 LC10 and TAA 10 with an occasional WCC/LC05/LC07. I did load up a mix with 55 fmj and Win748 which had a SD of 13 with ES in the mid 30's. It sizes and swages the same.
  13. P

    Reloading Equipment Processed 5.56 brass for sale

    I wasn't planning on it for just 1k cases. Should fit in a medium priority USPS box which is about 13 bucks or so. I can cover shipping on larger orders
  14. P

    Reloading Equipment WTB 5.56 LC processed brass

    https://www.snipershide.com/shooting/threads/processed-5-56-brass-for-sale.7101205/ Just listed some the other day
  15. P

    LWRCI REPR MKII Elite 6.5-CM Suppressor Issues ...

    Also you can use a HP bolt as well which is available that helps with primer piercing. For clarification are you piercing primers or simply blowing them out of the case?
  16. P

    LWRCI REPR MKII Elite 6.5-CM Suppressor Issues ...

    Lot to digest there but a general rule of thumb is to bump the shoulder .003 for semi use from a fired case. Depending on the throat you should also know you bullet jump as well to make sure you aren't jamming the bullets into the rifling. Check those things and report back. An easy check for...
  17. P

    Reloading Equipment Processed 5.56 brass for sale

    I have some brass that I need to move so I can buy some more toys, lol. All processed on a Dillon 1050, primer pockets swaged and trimmed. Headspace is set towards the small side on a Wilson case gauge but I can measure if you want me to. Tumbled in stainless media and ready to load. I have...
  18. P

    LWRCI REPR MKII Elite 6.5-CM Suppressor Issues ...

    If you're blowing primers it sounds like the loads are too hot or there might be a headspace issue. If you can turn the gas completely off I'd start there and see what the load look like. Also verify headspace with a fresh Vs fired case. With a can you are adding a bunch of dwell time past the...
  19. P

    SR-25 Muzzle Device Removal

    With rocksett it helps if the water is boiling and you can insert the muzzle end into the water for 15 min or so. They've always softened up for me that way.
  20. P

    advantage of extended gas length?

    An agb will help to get pressures correct but with a 22-24" tube and a small effective gas port you will have a sharp peaky pressure rise to the carrier which will be less tolerant of fouling and gunk so I would expect reliability to be less than that of a longer has system. For a range only gun...
Top Bottom
Back
Home
Forums
Merch
Alerts