• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. S

    Range Report 600 and 950 yard videos with DTA SRS 338 LM

    Washoe county range near Reno NV. Very gusty winds. Dialed 6 mils elevation and 1.3 mils windage at 950 yards. Fun and very challenging conditions. Great range. Highly recommended. Projectile pressure wave and reports. Target at 950 is steel plate just to left of yellow barrel. 4200 ft...
  2. S

    600 and 950 yard videos with DTA SRS 338 LM

    Washoe county range near Reno NV. Very gusty winds. Dialed 6 mils elevation and 1.3 mils windage at 950 yards. Fun and very challenging conditions. Great range. Highly recommended. Projectile pressure wave and reports. Target at 950 is steel plate just to left of yellow barrel. 4200 ft...
  3. S

    Where to buy Manfrotto tripods?

    Need a good tripod for my Leupold Mark 4 spotting scope. Any ideas on where to get Manfrotto's?
  4. S

    Kestrel 4500 Horus Review?

    Anyone have any reviews on this product?
  5. S

    DTA SRS Scope Placement

    Where are you guys running yours? I have the end of my S&B around the location of the start of the composite stock on the top and with two spacers (one removed) I measure approximately 11 inches from end of scope to end of stock. This feels right on the bench but I did a little playing around...
  6. S

    VIC-123

    Just received mine yesterday for some 338 Lapua reloading. Very pleased with the unit. At first I was a little confused as to why closing the lid would change the zero but after reading the instructions it says to keep the lid open during measurements. I found I had to adjust the leveling...
  7. S

    DTA SRS OAL 338 Lapua - What are you measuring?

    I just used my OAL gauge to measure the OAL in my SRS. I measured 3.645 to the lands. I reloaded .03 off of that (3.615). For some reason I thought it would be longer than that. What are you guys measuring?
  8. S

    Bench Shooting

    Ok, so I have been trying to practice the online training concepts but I have to fire from the bench instead of prone. I did shoot some nice groups with the SRS in 338 Lapua at 100 yards but found that since I am not straight behind the rifle that it always recoils to the left and I loose sight...
  9. S

    Range Report DTA SRS 338 Lapua

    Just finished the break-in on my DTA SRS and finally was able to take it to the range and actually shoot some groups. The break-in was interesting. Five 1 shot cycles and then following the DTA cleaning guide. The first shot took 4 cleaning rounds to get all the copper out. The second shot...
  10. S

    338 Lapua 250g Scenar HPBT COL (3.602 or 3.681)?

    Has anyone noticed that the factory Lapua Scenar 250g HPBT ammunition appears to measure 3.602 in length instead of their specified 3.681? I did some searching and found this on wikipedia. Can anyone confirm this? Just finished break-in on my DTA SRS with the factory Lapua and was puzzled...
  11. S

    Favorite hand-loads for DTA SRS in 338 Lapua?

    What are you guys running? Just ordered Redding Comp precision die set and have Lapua brass, Hodgdon H4831SC and 250 HPBT scenar's en-route.
  12. S

    Range Report Range Report - 460 XVR S&W Magnum Handgun w/scope

    I have been slowly sighting in my S&W 460 XVR handgun with Leupold VX-III 2.5-8x32mm scope. I had one flier and the rest were just dialing in the elevation and windage. Next report at 300 yards. Sorry for the low quality pics from my cell phone. Also included ballistics comparison to the 338...
  13. S

    338 Lapua reloading press and die recommmendation

    Just purchased a DTA SRS in 338 Lapua. What are you guys recommending for a reloading setup (press, die, etc). I currently have a Hornady lock-n-load setup for reloading my 460 S&W revolver but am not sure how well this will work with the 338. I see that they do have die sets for this...
  14. S

    Cerakote DTA SRS?

    Anyone have a DTA SRS with Cerakote? I would appreciate any comments you may have on whether or not to get it done. I plan to order a SRS in the next week. Thanks, L
Top Bottom
Back
Home
Forums
Merch
Alerts