Search results

Search the forum Search Articles
  1. 81STFACP

    Win an RIX Storm S3 Thermal Imaging Scope!

    Service rifles, steel and wood. Irons, no stinking optics.
  2. 81STFACP

    M40a1 build guide

    Thank you. We served in the same unit, retired from the same company... friendship spanning close to 50 years. We even live 2 miles from each other
  3. 81STFACP

    M40a1 build guide

    A friend willed this one to me. Returned stock complete with bottom metal. 6 digit receiver. Scope is the old Weaver T10.
  4. 81STFACP

    What AR15 cartridge is a worthwhile step up from 5.56?

    Go for it, tell us all about it.
  5. 81STFACP

    What AR15 cartridge is a worthwhile step up from 5.56?

    Make one a Franken14. 2500 fps with M118 LRs. With the Salmon River Solutions 5 port Ti brake reduced recoil, shooting prone at rattle battle pace is a lot more fun compared to full blown standard 14.
  6. 81STFACP

    What can cause accuracy to fall apart at 700 yards?

    Button or cut? Do you know the twist tolerance of either one? One time we had one button AR barrel stamped 8T, but it would stabilize any 80 trainer. At 600 it was 8 ring to 8 ring for normal distribution. We handed the shooter another rifle, he shot 200-11X. We surmised the 8T he had maybe...
  7. 81STFACP

    Bolt carrier for precision AR-15

    Depends on your comfort zone, 0.001 on each side. Measure ID of upper tailside, turn down sleeve to fit.
  8. 81STFACP

    Bolt carrier for precision AR-15

    Yes. Start with with 1 inch SS tube 1/8 or 1/16 wall. Turn down OD to fit, bore ID to accommodate however thick JB you wish to employ. Remove finish and rough up the BCG tail section
  9. 81STFACP

    Bolt carrier for precision AR-15

    I have been using my own enhanced BCG for years. Fitted sleeve, JB Welded, then slot cut. Due to oversized tail, the buffer tubes are bored and polished. The old brake cylinder hone in the tailstock does a good in polishing the bored out tube. The one with pressed in brass plug is the same on...
  10. 81STFACP

    USMC XM-3 clone

    What seems to be going prices on the FA762SS these days?
  11. 81STFACP

    BUIS on AR15

    Here is the 16 inch carbine I built for an LT at Benning. He wanted this configuration, folding front (also the gas block like the standard M16 a frame) and rear sight bases. No idea where he sourced the parts. But, I like them. Better built than what I normally see. What a pain to modify the...
  12. 81STFACP

    Does Bartlein, Kreiger, and Proof carry as much weight in the AR world as they do in precision rifle bolt-action guns?

    Frank posted this score sheet in another thread before. 3rd match of the 2023 CMP Cup. Frank donated the Bartlein blank, I spun the 20 inch service rifle barrel for a Texas Junior. She won the match over some of the best in the business.
  13. 81STFACP

    Knives Steve Woods Hide Fighter SOLD SOLD

    I special order one from Steve with stag instead of G10. Still have it. At that time I think he just made 2.
  14. 81STFACP

    77 gr Sierra SMK’s deer hunting

    Thank you. I run the M118 LRs through a Giraud meplat cutter. Suppressed 16 and 22 inch gas guns, never had a hog run off with boiler room shots. No exit holes.
  15. 81STFACP

    77 gr Sierra SMK’s deer hunting

    And, I'll say it.... Match bullets are not meant to be used as hunting bullets....
  16. 81STFACP

    300 Win Mag Match Chamber?

    Choose your poison. After chambering multiple barrels of mine with differenr reamers, I went back to SAAMI
  17. 81STFACP

    Wearing out a 308Win barrel

    Not a bolt gun, but double lug 14, 32 pounds of powder.
  18. 81STFACP

    Recommend the most American made 30-06 for an elk hunt

    Circa Summer of 1974. Cape Lisburne, home for a year my Uncle sent me to keep an eye on Ivan on the other side of the Straight. No fancy camo, no signature boots, just Chuck Taylors and wool socks.. when warm enough on our hikes down the damp tundra of the Caribou Valley, or the beach of the...
  19. 81STFACP

    Recommend the most American made 30-06 for an elk hunt

    Swr I chambered the 28 inch KBI with a Serengeti
  20. 81STFACP

    Recommend the most American made 30-06 for an elk hunt

    You are right, why launch a 180 when you can a 215 Berger @2840 from a 28 inch tube. Dang, my brass are too old.
Top Bottom
Back
Home
Forums
Merch
Alerts
You must be at least 18 years of age to use this site
You confirm that you are at least 18 years of age by continuing to use the site.