Search results

Search the forum Search Articles
  1. 6MT

    Anyone manually dump and trickle on a A&D FX120i?

    I manually trickle all of my calibers using TiteGroup. I use the Lee dipper scoops and the Lee Perfect measure for bulk throws. But then I use the V3 trickler to trickle up to finish. Mostly because the V3’s bulk thrower can’t get as low as some of my charge weights require. It works very well.
  2. 6MT

    Caldwell Velociradar vs. Garmin Xero

    He certainly isn’t Jeremy Clarkson.
  3. 6MT

    Does anyone still use case gauges?

    I agree. But they do have their uses. I use them on fired cases to see where the brass is moving. Also I find them useful for my hunting calibers when I use tighter neck tensions. Seating bullets with .004” tension can slightly deform certain “fatter” cases above the base (6.5prc is a good...
  4. 6MT

    6.5 PRC Loads

    Whidden bushing die & micrometer seating die.
  5. 6MT

    Precision Rifles.....show em!!

    That’s pretty!
  6. 6MT

    New 3rd generation AndiScan A3 ballistic Doppler radar

    Thank you.
  7. 6MT

    New 3rd generation AndiScan A3 ballistic Doppler radar

    An acoustic trigger? Really?
  8. 6MT

    Tripod noob - Innorel RT90C setup

    I guess so. But not with me. When I use it to hunt, I’m usually at a stand. Weight is not a mobility issue. Weight for me, is all about stability.
  9. 6MT

    Tripod noob - Innorel RT90C setup

    I agree the Arca is much better. But my hunting rifles don’t have the Arca mount. I do use the tripod with my match rifles. They all have the Arca rail.
  10. 6MT

    Tripod noob - Innorel RT90C setup

    I also echo the RT90c and N52 praise. I use mine when stand hunting. I have yet to try it in competition. I use both the Hog Saddle and the ARCA plate. That all depends on which rifle I’m using. I am pleased with the stability of the platform.
  11. 6MT

    MESSED UP STUFF YOU’VE DONE AT YOUR RANGE

    I got to try a JM Marlin about ten years ago at my range. I was excited because I always wanted one. I was so excited that I forgot I had no ears on. Ouch, that hurt!
  12. 6MT

    CZ P10 review

    I have the P10-F. It has proven to be a very accurate pistol. The ergonomics fit my hand pretty well. I have found it to be “loud”. Sorry, that’s just hard to explain any better than that. It is very reliable and has never not gone boom. (I’ve only ever shot 124gr factory 9mm ammo.) I’ve never...
  13. 6MT

    Sidearms & Scatterguns Handguns...show 'em

    Just a few wheel guns…
  14. 6MT

    What did you do in the reloading room today?

    Freshly annealed 6.5prc cases…
  15. 6MT

    -E error on FX120i

    Mine does the same when I turn it on and remove the cup (after the scale goes through its checks). Recalibrate. No issue.
  16. 6MT

    Runout with FL sizing. Any help?

    Just a thought. Maybe the OP should try a free float press.
  17. 6MT

    Prince called, he wants his rifle back…

    Gawd, I wish my Wife would say that!
  18. 6MT

    Burnt brass

    Not sealing properly in the chamber(?). Possibly a light charge weight(?). I have a light plinking load in .45 Colt that does that in a Uberti 1873 clone. No biggy really. Hopefully they are accurate. So, clean ‘em, and reload them.
  19. 6MT

    28" 6.5 Cr.

    I didn’t say it was bad. But it seemed long for maneuvering in prs. I’ve seem mostly 24’s and a few 26’s up here.
  20. 6MT

    28" 6.5 Cr.

    This is my CM rig with a 28” 1.25” straight contour 1:8” barrel. With 44.0gr of IMR4350 and the Berger 140gr Hybrid Target bullet, my velocity is 2880fps average. If you’re going to do PRS, wouldn’t that 28” pipe be a tad long to maneuver easily?
Top Bottom
Back
Home
Forums
Merch
Alerts