Search results

Search the forum Search Articles
  1. P

    MDT ACC Premier Gen 2 experience? review?

    I have my Vudoo 360 with a 22” straight Bartlien barreled action in one and it is a perfect fit for me. Comes in just above 15 pounds. Matches my centerfire rifle in an ACC as well. The 15” fore end Is just about right and leaves plenty of support for balance. I will say the adjustable butt...
  2. P

    SD's

    I shot 34 rounds today and got an SD of 4.0 6 dasher in Alpha brass I am more concerned with ES
  3. P

    Need to build a linear moving target

    Yes I have seen comments on garage door opener but you need to use Commercial duty ones to run it all day in a match. If they were reliable, it is a good start. A mover at a range in NY was a Ferris wheel type with 4 rimfire targets, homemade also. It had adjustable speed. Not linear but a mover.
  4. P

    Need to build a linear moving target

    I was looking at these for rimfire mover for matches where we have berms. I was thinking make up a track of some kind for behind the 100 yard berm, and have a sled of some kind on maybe roller skate wheels or something attached to this so the cable is protected, the sled is also behind the berm...
  5. P

    Maggie’s The Wood Shop

    I finally built this bedroom set my wife has patiently waiting 20 years for a few years ago. I just noticed this thread, there is some really talented folks on here. And here is a YouTube I put together of my build.
  6. P

    Looking for some help with my prone shooting in MA

    Where in Mass? I’m on the south shore
  7. P

    Hornady Bullet Comparator and OAL Tool Measures over .050" too short

    When I use that tool with a modified case, I can never get the calipers to line up perfectly straight in line because it is on an angle. Maybe your measurement if off because of that I don’t know but that could explain the discrepancy. Or like others have said, forcing into landscaping has gone...
  8. P

    Maggie’s Things Trump Should On His First Day............

    I’d be more concerned with what he does now, way before his first day as far as SS protection. He needs some overwatch to oversee and prevent incompetence or bias.
  9. P

    Unexplained elevation shift, reason?

    I checked the set screws on the turret of the Razor HD and yes, it had one screw backed way out so it probably was not engaging and surely the reason for my trouble. I will need to add that to my checklist from now on. THANK YOU! that is a relief to know at least. I will still confirm once I...
  10. P

    Unexplained elevation shift, reason?

    Parallax was good variable wind from behind but that only affected left or right and it switched on us as we shot going 7:00 or 5:00, small enough plate to give a lot of us at that time trouble, but nobody zeroed that stage but me, and only a little slope downward 2 degrees at most. temp would...
  11. P

    Unexplained elevation shift, reason?

    I did not check those, thank you. I have found those to be loose before so that rings a bell. I will check You may be correct and it sure sounds like it Thank you!
  12. P

    Unexplained elevation shift, reason?

    yes solid. and prone afterwards solid did the same no change to the rifle other than the scope cap being depressed down and then up again to return to zero between the stages.
  13. P

    Unexplained elevation shift, reason?

    nope, all same ammo 30.7 grains Varget 105 berger hybrid 10,000 off lands Not in sun, took last mag from backpack and figured out I was 2 mils high at 500 yards after we were done for the day. Crazy I know.
  14. P

    Unexplained elevation shift, reason?

    That is what I thought, Vortex Razor HD gen 2 I will No suppressor, a Hellfire muzzle brake and it is tight, not loose at all.
  15. P

    Unexplained elevation shift, reason?

    This may be long but bear with me please. Yesterday I shot a finale and on my last stage of the day my misses were all high 2 mils. This was a barricade timed stage 400 yards and 500 yards on 8” plates. Grass behind so not much for feedback as I was missing I adjusted for wind only a couple...
  16. P

    Rimfire Vudoo V22 AICS Single Shot Adapter, Bolt Disassembly Cocking Tool, Mag Loader Tool, Magazine Bench Tray, Bullet Lifter

    I would like to get one of each of these for my v22 360 single shot adapter "pen" holder set of 5 magazine caps bullet tray lifter box for Lapua Thank you
  17. P

    Factory Vudoo lead time (straight bartlein barrel)?

    I went with target crown since I have no intention to put a tuner or a suppressor on it. Got a great group of 5 Midas plus at 50 yards last time out, now over 300 rounds on it. 0.15”
  18. P

    Ingenuity Precision trickler

    Hopefully I can purchase one of those
  19. P

    Please tell me this can’t happen. Won’t happen.

    How many is more
  20. P

    Factory Vudoo lead time (straight bartlein barrel)?

    22" is now ready. maybe Bartlein sent 22" barrels but not yet 24" barrels, who knows. Anyway it should be worth the wait.
Top Bottom
Back
Home
Forums
Merch
Alerts