Search results

Search the forum Search Articles
  1. Gun_Guru

    Best 6.5 Bullet for 6.5 PRC

    I just picked up my new rifle . 24” 1/8 twist 6.5 PRC. Built On a SA. I am debating between what bullets I want to use. I would like to Be around 3200-3300. What’s y’all thoughts ? I will be hunting whitetail, Mule deer , elk , pronghorn.
  2. Gun_Guru

    Need some help

    I'm new to reloading and trying to figure this out . I have new Lapua 6.5 creedmoor brass. The neck is super tight and I want to open them up ( or do I even need to) . I am using a Redding full length type s sizing die. Can I lube the brass and run it up over the mandrel to open them up? If I...
  3. Gun_Guru

    Manners Composite Stocks Estimated Lead Times

    Found a MCS CS in scorched earth in the flat top section .. Y'all need to check there..... Because I need to slow down
  4. Gun_Guru

    What's going on???

    So you claimed it did more harm then good , then you refer to a test that proved it was a identical outcome . Maybe I'll sacrifice a chicken to understand your logic .
  5. Gun_Guru

    What's going on???

    How so?
  6. Gun_Guru

    What's going on???

    I'm not one to claim barrel breakin is needed on good barrels or does it help, but I also think it can't hurt
  7. Gun_Guru

    What's going on???

    I thought the same at first. Ran 10 dry patches and swabbed chamber until it was as dry as Hilary's vag...
  8. Gun_Guru

    What's going on???

    I'm always checking to make sure it's not lose , and I make sure the cover never gets near the start of the anchor break( end of my omega )
  9. Gun_Guru

    What's going on???

    Well that's good to know... I really should start reading lol
  10. Gun_Guru

    What's going on???

    89
  11. Gun_Guru

    What's going on???

    I did take the suppressor off when I took a break and then put it back on. I did throw on the magneto speed and I didn't have any spikes or anything that looked weird
  12. Gun_Guru

    What's going on???

    I agree with you on the factory ammo. I have over 14 precsion rifles and all of them shoot 1/2" groups with a handful of differnt factory ammo. I already talked to mark at Spartan Precsion about it. He's a solid guy and said he will look it over I just want to avoid another 2-3 week wait if I can .
  13. Gun_Guru

    What's going on???

    I agree on break in. I shoot 3 single shots then 2 3 shot groups and off to the races . After that I shot 80 rounds with no cleaning . I don't clean my rifles Until they need it.. ( obv I manage carbon in chamber ext)
  14. Gun_Guru

    What's going on???

    Brand new AtacR 7-35. I took it off and threw it on my 6.5x47 to check scope and was perfect . And it's not a mini chassis . Glass bedded.
  15. Gun_Guru

    What's going on???

    I hand load as well. I normally break them in with factory loads then startu work up. I shot all the same ammo in 2 other guns and have all under 3/4 groups average being 1/2.
  16. Gun_Guru

    What's going on???

    Yes all shot were with suppressor except the first 3 single shots then first 2 3 round groups . It was 72 degrees , 80% humidity and been raining here for 1 week. Got a break in the rain so went shooting
  17. Gun_Guru

    What's going on???

    Yes I fired one shot the removed copper. Did that 3 times ( wiping chamber dry after every cleaning ). Then went to 3 shot groups then cleaning .
  18. Gun_Guru

    What's going on???

    Yes scope base torqed to 50 inch lbs, badger rings ( cross bolt to 65 inch lbs) and rings at 22 inch lbs
  19. Gun_Guru

    What's going on???

    I will add bolt was not heavy to close .. During high pressure heavy lift tho.
  20. Gun_Guru

    What's going on???

    I took my rifle out today for the first time to break it in and get some groups on paper. Rifle is a bighorn Tl3 , bartlien heavy palma 6.5 creedmoor 24", manners elite t6a, trigger tech blah blah blah ... All best of the best. I did a proper barrel break in . I tested hornady 147 m, 140m, 143...
Top Bottom
Back
Home
Forums
Merch
Alerts