Search results

Search the forum Search Articles
  1. Bladeweaver

    I broke the pin in my Lee decapper...

    Re: I broke the pin in my Lee decapper... You can get the pins almost anywhere. Right from Lee or somebody else like Graf's or Midway USA. I have about 6 extra on hand, just in case.
  2. Bladeweaver

    Timney or Jewell?

    Re: Timney or Jewell? ok, ok... Yes, in all actuallity, it may be about 1500 rounds in 3 days on the high side. I exaggerated it due to the fact that it was kind of being called a more of a "pretty" gun than a used gun. IMHO, even if it were 300 rounds a day for 3 days, I would still...
  3. Bladeweaver

    Timney or Jewell?

    Re: Timney or Jewell? I thought 3000 rounds in 3 days was used and dirty......my bad...
  4. Bladeweaver

    Timney or Jewell?

    Re: Timney or Jewell? This one is going into a precision rifle, not a tactical.
  5. Bladeweaver

    Timney or Jewell?

    I didn't want to hijack anothers thread so I started this. I have used Jewell triggers in AR platforms before. I can't say I have had any problems and they can be adjusted to a very light first and second stage. All in all, I can say I am happy with them. I have seen a lot of advertising...
  6. Bladeweaver

    Spotting Scope Base

    Re: Spotting Scope Base It's not a real gem. That's why I am looking for something different. Something more functional and rugged.
  7. Bladeweaver

    Spotting Scope Base

    I have a half way decent scope and a good range finder. Right now I have my spotting scope on top of a camera tripod. I find that it is quite unstable and jiggly. What should I be looking for for a good base for it? Something that can be used on table top or uneven ground would work well I...
  8. Bladeweaver

    Rifle Scopes Varmint rifle scope

    I'm putting toether a varmint rifle for some prairie dog hunting next year. It will be a .223 platform with a 1/10 twist barrel. I plan on shooting a 50gr bullet (give or take a few grains). I'm looking for scope suggestions. All hunting and shooting that I hsave done so far has been at...
  9. Bladeweaver

    Suppressors springfield xdm

    Re: springfield xdm I just did a great trigger job to a friends XD45. Now the firearm that he loves all except the trigger is just a firearm he loves. No more creep, no more overtravel and just a clean 3.5lb trigger. I was able to get the parts at my cost for about $90.00
  10. Bladeweaver

    looking for the thread on .....

    Re: looking for the thread on ..... Sweet it was in chapter 4 sticky. Sorry I couldn't find it. I make a copy and saved it off now too..... Tomorrow, back to the range.........
  11. Bladeweaver

    looking for the thread on .....

    Hello all! I know, I know, I must be blind. I know I saw it here and I haven't been able to find it by search function..... I know there was a write up on determining the proper load for your rifle. It went into depth on loading a certain bullet and powder in different weights and then...
  12. Bladeweaver

    Rifle Scopes ACOG TA33 / EoTech / Aimpoint

    Re: ACOG TA33 / EoTech / Aimpoint I have a few AR's. One of them I have equipped with the Aimpoint CompM3 and the 3X magnifier. I have them set up so they will co-witness my iron sights. The 3x is on a quick flip mount so that I can easily flop it to the side and just use the M3 if needed...
  13. Bladeweaver

    What heater for Reloading Room in garage????

    Re: What heater for Reloading Room in garage???? Because I park a car in my detached garage, code here says my flame has to be six feet off the floor. My only option here is a horizontal ceiling mount Modine heater. I run one on a 100gal LP tank outside and keep things at 45 degrees min so...
  14. Bladeweaver

    .308 favorite accuracy loads

    Re: .308 favorite accuracy loads Thanks for all the reply's! Lots of good info here for sure. I have ordered a few Molly SMK's and some Varget. I will try those in addition to what I have already. It soulds like the SMK's are a big favorite. I'll give some loads some tests and then...
  15. Bladeweaver

    .308 favorite accuracy loads

    I'm going to be off to the test range soon and I have worked up some loads for trying to see what shoots best out of my gun. What are your favorite .308 loads? I am going to be shooting 165gr. Nosler Ballistic Tip, 168gr. Sierra BTHP, 168gr. Hornady Moly BTHP, and 178gr. Hornady Moly A-Max...
Top Bottom
Back
Home
Forums
Merch
Alerts