Search results

Search the forum Search Articles
  1. Regular Guy

    tactical pants

    Duluth trading ultimate flex firehose work pants with the knee pad inserts. If you don't want the knee pad slots built in, the flex firehose pants are a bit lighter (cooler in the summer) or the dry on the fly nylon based pant. I like my TAD gear pants too, but the duluth pants are the same...
  2. Regular Guy

    Suppressors Are these damaged baffles? SF-SOCOM762 on a Seekins 300 Blackout 16" barrel

    Surefire has installation notes that specifically voids the warranty if the mount is not installed properly. Crush washers are a no-go -- Surefire shims only. That being said, I do recall a thick shim being included with the surefire shim pack. Are you certain it is a crush washer? It will...
  3. Regular Guy

    Remington 700 Switch-barrel - Why wouldn't this work?

    I ran a switch barrel for F-class for years that was very lightly torqued - I didn't need more than 20 ftlb. Try shooting groups tightening in 10 ftlb steps to see if you see a difference. I didn't. I settled on 20 ftlb since the removal torque matched the install torque there. Any looser and...
  4. Regular Guy

    Any 777 pilots here? Can the cabin pressure be shut off at the cockpit?

    Easy boys, no need for personal attacks if you disagree with someone. Will the triple make it to 450 - most likely it will depending on weight. Yes, that is above it's certified service ceiling. There are additional requirements for certification for flight above certain altitudes, so the...
  5. Regular Guy

    High Quality Kitchen Knives

    If it hasn't been stated already, check out Carter. He is a fellow precision rifle shooter and makes unbelievable knives! He trained under a master in Japan for 17 years before being released to start his own forgery. Carter Cutlery - Your Source For High Performance, Hand Forged Cutlery
  6. Regular Guy

    Pupil of the Art of the Tactical Rifle Dot ORG *Video*

    Damn near pissed my pants! I thought it looked like a Surgeon Malpractice action to me, but that Stiller Chlamydia looks like she works pretty good. I take it she has been "used" by other operators a number of times? Or was she a virgin receiver when you got her?
  7. Regular Guy

    Rifle Scopes ADVICE! High-Power, FFP, Mil-Mil, 10-Mil/Rotation Rifle Scope

    Directly from Ian Kelbly. They announced it at SHOT.
  8. Regular Guy

    Rifle Scopes ADVICE! High-Power, FFP, Mil-Mil, 10-Mil/Rotation Rifle Scope

    Kelbly's will have the new version of the March 5-40 with .1 Mil clicks ready for delivery shortly. I have the 3-24 now and will be picking one of the 5-40 up as soon as they come in. Great scopes - especially for the price...
  9. Regular Guy

    "EddieG1979" aka Tactical Rifles Shooter

    No, I didn't have the right stuff to go tier one. Those guys could clean a shitter lickety split!
  10. Regular Guy

    "EddieG1979" aka Tactical Rifles Shooter

    My favorite was cleaning the cracks in the sidewalks. That's some hardcore tacticool chit right there!
  11. Regular Guy

    Gunsmithing Cerakoting ring interiors.

    Cover the inner area of the rings in blue painter tape and cut it along the edge so there is no overhang. You will have to replace the tape after blasting and before painting. Comes out perfect.
  12. Regular Guy

    Which Switchblock? Does it REALLY matter?

    Does your block fit under a Noveske NSR rail?
  13. Regular Guy

    Jewell triggers are pussies

    I have had good luck with allowing longer overtravel - tip I got from a F-class shooter - and have not broken another one since; even with pierced primers.
  14. Regular Guy

    Jewell triggers are pussies

    That is a well known issue with Jewell triggers. Stop piercing primers - load lower or have the firing pin bushed - or switch triggers. FWIW: I have had factory rem triggers break from pierced primers too.
  15. Regular Guy

    Which Switchblock? Does it REALLY matter?

    The switchblock gas tubes are not standard tubes and are already attached so you would have to cut it shorter which may lead to issues. Also, I believe the porting in the block is tuned for length.
  16. Regular Guy

    Fieldcraft How to carry heavy barreled beast

    Put that thing on a diet! The older I get the more I realize I am no longer the twenty something I wish I still was. I have gone to lighter tapers and shorter barrels and don't feel I have given up much, especially when I factor in that I am much less tired when I go to take a shot.
  17. Regular Guy

    Gunsmithing barrel work after cerakoat?

    Depends on how it is done. On a steady rest you will wear away finish, thru the headstock should be fine especially if using a soft metal between the jaws and the barrel. I have done a number thru the headstock with no noticeable wear to the Cerakote.
  18. Regular Guy

    Gunsmithing Cerakote coming off

    Yep, exactly. To keep the action smooth and prevent binding it needs to be applied very thin and blasting with AL oxide - which is what NiC recommends - is a bad idea. I have been applying Cerakote to guns since the product came out. Even if applied per spec the finish will wear due to the...
  19. Regular Guy

    Sidearms & Scatterguns M&P Pro sights that clear a can?

    I don't think they do any color of tritium other than green. You would have to ask them. Their prices are on their website.
  20. Regular Guy

    Sidearms & Scatterguns M&P Pro sights that clear a can?

    Sent some pics. I don't know if they do any color other than green tritium. Never hurts to ask.
Top Bottom
Back
Home
Forums
Merch
Alerts