Search results

Search the forum Search Articles
  1. W

    Any Old Remington Employees Here, or Smiths Experienced On the Remington 700?

    SAY WHAT?? I'm....speechless...
  2. W

    338 Lapua mag build

    Action is irrelevant, all that matters is the mag length in the context of your question. I recently chambered/rebarreled one (Bartlein blank), SAAMI spec reamer. Berger 300 Hybrid OTM's were one of the load-workup choices, along with 250 Scenars and 300 A-Tips. The burned-up barrel it...
  3. W

    Dave Tooley contact info

    ^^ He's on the accurateshooter forum all the time (gunsmithing forum).
  4. W

    .308 headspace question

    IF you handload you already know to adjust your shoulder bump accordingly so as not to keep overworking/stretching the brass unnecessarily...
  5. W

    Anyone familiar with the pillar bedding offered by Boyd's with their stocks?

    RIchard's Microfit is a solid alternative for walnut and laminate stocks if you don't mind doing the final fitting and finishing. I'd rather do final fitting/bedding/pillars on a stock that hasn't had the exterior finish applied.
  6. W

    who likes the 300 wsm ?

    From NZ... https://www.ballisticstudies.com/Knowledgebase/.300+Winchester+Short+Magnum.html The .300 WSM achieves what its designers intended, duplicating the velocities of the .300 Win Mag from a short, lightweight rifle platform. Generally, the savings in length are approximately 2.5” when...
  7. W

    who likes the 300 wsm ?

    How so? It does just fine. 208 ELDMs in mine... https://bulletin.accurateshooter.com/2021/03/sunday-gunday-300-wsm-pending-1k-world-record-heavy-gun/
  8. W

    who likes the 300 wsm ?

    .300 WM and .300 WSM are ballistic twins. Pick one... .260/6.5 Creedmoor .243/6 Creedmoor Potato/Potatoe
  9. W

    Very disappointed

    Contact CZ cust svc to find out what match ammo they use to verify sub-3/4 moa accuracy (their website states every rifle's accuracy is "verified". Then I'd get a box and see...
  10. W

    Barrel vice and action wrench kit?

    Chamber cast will be- you're clamping the barrel a foot ahead of the chamber. It's obviously not going to affect the chamber behind it. Barrels should always be clamped just ahead of the receiver ring.
  11. W

    .300 PRC Barreled Action Recommendations

    ^^^ This. Yes, you can shoot a 6.5 Creedmoor or just about anything else out to 1k and beyond- just point the bore skyward. Spotting your impacts needs to be considered, tho- and that's why I shoot a .300 WSM at 1K+ and a 7-08 inside of that.
  12. W

    Hot barrel was hammering…why

    Makes sense, could be. Heat expands the barrel (from inside out obviously=bore), stiffness is reduced, and harmonics change. Could be any or all of the above contributing to it. I'm sure you know strings like that will toast the throat (and accuracy) in short order with what's already a burner...
  13. W

    Savage 111 rifle, I just mesured the action the female thread is .006 off to the left. Also I can't understand why barrels are centered on a thread. A

    Welcome to the forum. I'm still trying to understand your thread title- what exactly you measured, and how... Internal receiver threads "are .006 to the left"- of what? "Barrels are centered on a thread"- huh?
  14. W

    Rechamber question 243 Ackley to 6GT or something else?

    No. Much more than a "setback"- it's time for the bandsaw on that one. Plus, new bolt... 6 ARC bolt gun should be built off a Howa mini in 6.5 grendel w/ a barrel swap for the easy button.
  15. W

    Should I go magnum?

    Short action = .300 WSM. Maybe a 7/6.5 PRC if ya don't mind a wildcat. Long= .338 Lapua Shooting a mile can be fun, or frustrating. Consider your conditions- private or public range? Can you set up a camera? Hit indicators on steel? You need to be able to spot your impacts- if you can't you...
  16. W

    Federal does it again 😅

    Perhaps with higher pressures, and steel/hybrid cases it'll get closer. Still going to be limited by short barrel length and case capacity, I don't see how those limiting factors can be overcome. The NATO 5.7x28 SS190 will do 2350 fps from a rifle length barrel, albeit with a 30 grain boolit.
  17. W

    Federal does it again 😅

    I understand bolt thrust- and that's exactly my point. A typical production short action with the common .473 +/- boltface isn't designed for 80,000 psi cartridges. It's designed around chamber pressures in the low 60's. Of course there's significant safety margin- but that's irrelevant as to...
  18. W

    Federal does it again 😅

    I would love to know This is THE only question I have. Different alloy? I mean, they can't change the dimensions of the receivers- too much rides on that standardization. Or, are they gonna tell us they've always been good for 80,000 psi? Savage...
  19. W

    Federal does it again 😅

    As well you should be. It's bullshit. Equal and opposite reaction, remember? It's a "law"...
  20. W

    Tikka Action bluing wearing off

    In addition to small parts, I once did an entire barreled action for an Israeli Mauser that had a fair amount of surface rust. Blasted it and applied multiple coats of Oxpho. It takes some work and there's technique to the application to achieve an even finish of the desired depth of color, but...
Top Bottom
Back
Home
Forums
Merch
Alerts