• Winner! Quick Shot Challenge: Caption This Sniper Fail Meme

    View thread

Search results

Search the forum Search Articles
  1. D

    Hunting & Fishing 300 WSM recoil in light rifle?

    I have a Browning a bolt with a wood stock. The gun is a tack driver with 150's and 168 a max. The one issue i have with the 150's is the sharp kick. When I load up 168's the kock is still there but turns into more of a push. And I'm sure if you went with the 180's it would be even more of a...
  2. D

    After many... these are the ones that work for me.

    Nice selection.
  3. D

    Whoa! Dad teaches daughter about car crashes while driving....

    Ouch!!! That's going to leave a mark
  4. D

    Anyone here refinance a home loan lately??

    I bought my house two years ago with a 4.625 % va loan. Ive defied 2x. first refi brought me down to 3. 625 that was about a year go. and my last one was a few months ago was down to 3.125%. all these loans are va loans. Also it helps to be friends with mortgage brokers. They can get lower rates.
  5. D

    Lots of blemished bullets and brass in-stock

    Sh it. Just what I was looking for and I missed out. Work is always getting in the way.
  6. D

    Ryan from Green Bay

    Welcome aboard Ryan. I'm also from green bay. Where do you usually shoot?
  7. D

    Rifle Scopes loose rings on mount

    Thanks guys. I made sure that the clamps were aligned before tightening. I'm going to push one ring forward against the forward slot and one back so it makes a sandwich between the rails. Is this acceptable or should I do what "flight" said and have both forward. .
  8. D

    Rifle Scopes loose rings on mount

    Hey gents, As you guys can see I'm a new member but a long time reader. Anyways I just picked up a set of nightforce bases (2 piece) and a set of badger rings. When I place the rings on the bases there's slop in the rails. What am I missing here? Did I pull a rookie mistake? Any advice...
  9. D

    Explosion in West, Texas

    Damn what's going on this week. First Boston now this. My thoughts and prayers go out.
  10. D

    Westboro basptist church at it again. sick

    These crazy fucks think that god sent those bombs. Now they want to protest at the funerals.
  11. D

    Westboro basptist church at it again. sick

    This story is no longer available - Washington Times This just makes me sick.
  12. D

    Newbie from Western WI

    welcome aboard, I'm on the eastern side of the state(green bay) but have a cabin in central part of the state.
  13. D

    Lots of blemished bullets and brass in-stock

    No the ones I have are almost chartues
  14. D

    Lots of blemished bullets and brass in-stock

    Did anyone buy the 168 grain 30 cal blemished? I just received mine and I'm lost as to what kind they are. They have a bright green pylomer tip. They almost look like zombie bullets. Any ideas?
  15. D

    .22 53 grain blemish at midway usa

    i snagged up 500 .22 match and 500 .168 30 cal. last week. Now this week i get theses 500 bullets yesterday along with 3000 sr primers from a local store. its like i hit the lottery
  16. D

    Insomniacs

    Belletmoto your right. But I Probably won't get much sleep tonight. Excited for my new gun. Probably get the scope mounted after I pick it up
  17. D

    Insomniacs

    Chubby, What's with the joke's? You have some jacked up shift hours. What do you do for a living
  18. D

    Insomniacs

    Well I've been away for the last few days. But now I'm back at it again. Its going to be another long week. 40 parts need to be shipped by Friday at 3pm. At 2+ hours of run time ill be working 15's this week. But several pulses to look forward to. Tomorrow ill be picking up my rem 700 r5 in...
  19. D

    .22 53 grain blemish at midway usa

    Just stumbled across these why placing a different order. Bullets are in stock so grab them quick. Blemished Varmint Bullets 22 Cal (224 Diameter) 53 Grain Polymer Tip Does anyone have an idea who these are made by?
  20. D

    Gunsmithing Need to "fix" the threads of my barrel (improperly machined.)

    If i was you I would go to local hardware store or machine shop and ask to use a thread file. This is basically a file that has the pitch of the thread cut into. It would be a lot easier then a single point file.
Top Bottom
Back
Home
Forums
Merch
Alerts