feeding

  1. D

    Yugo M70 won’t feed HP reliably

    I have a ZPAP M70 that will run fmj just fine but when I run hp, 3 or 4 rounds will run fine and then one will hit the side of the chamber and get hung up. I’ve seen threads about this and about filing the bottom of the chamber, but in my rifle the rounds are hitting all around the chamber. Not...
  2. Dre

    Precision Rifle Gear Victrix - Magazine Issue

    Heyo! First time posting here so if I make a mistake in channel please bear with me. I recently purchased a Victrix Armaments Gladio T and absolutely love it, except for the fact that I am having some serious issues with the magazine not feeding correctly. There is very little information out...
  3. R

    AR10: Occasional Jam

    I'm getting an occasional jam in my Armalite AR10 in .260Rem. This is particularly annoying when it happens during a match. The bolt goes back far enough to catch and chamber a round, but the fired case is not ejected. (images are a recreation of what happens) The equipment is: - Armalite...
  4. slickalaus12

    T3 Feeding Issue

    Hey guys, Yesterday I pulled out my T3 Hunter 30-06 to shoot it a few times at the range before my next trip. I have never had any cycling issues with it but yesterday I was having to use alot of force to push the bolt down to lock it into place on most cycles. Some were the normal, smooth...
  5. B

    Suppressors AR 5.7/ Spectre feeding issues?

    I've got a AR 5.7 upper and a SWR Spectre can for it. The gun has functioned flawlessly (800+ rds) w/out 1 jam. I have major feeding problems w/ the can on? I have also tried my M4-1000 on it w/ no luck. I know that it's blowback and not a DI gas system, and I used the supplied buffer w/ the...
  6. Known

    Gunsmithing Feeding problem with Badger M5 trigger guard

    Hi, I'm having an occasional feeding problem with the Badger M5 setup. I installed it using the pillars supplied with the kit. The rifle is a .308 chambered with a Palma reamer. Receiver is a factory Remington 700 Left Handed short action. Brass is brand new Lapua. Bullets are 155 scenars...
  7. mattsnuked

    Gunsmithing DPMS LR308 feeding problems

    Well I have had my DPMS LR308 for a week now and have taken it out to the range twice. I like the rifle BUT I have an issue with it. On only the 3rd and 2nd to last round in the mags when the bolt goes to cycle it skips over the head of the round, starts feeding the round by grabbing the body...
  8. Guns4570

    DTA SRS feeding test....

    I received my 338LM conversion late last week and wanted to mount up the barrel. So I read the manual on the steps; laid out the stuff in front of me with the right tools (torgue wrench from DTA and the integrated all in one tool kit). Set the timer and swapped the caliber in 57 seconds...
  9. A

    Gunsmithing Savage 10 FP Mag Feeding Issue

    I have a Savage 10Fp in .308 attached to a B&C Duramaxx stock-My 3rd rd out of the 4 rd mag continually is pushed out of the receiver prior to feeding by the bolt. 1st and 2nd rds feed fine-3rd ends up being spit out onto the bench or ground. 4th rd is fine-Today I experimented a bit and loaded...
  10. A

    AICS + REM 700 PSS = Feeding problems from the mag

    Hello, I have and AICS 1.5 on a remington 700 PSS. However, testing it out I noticed that feeding from the magazine results in my bullets being scraped along the feeding ramp and i have to apply a generous amount of force to get it up the ramp. Manually loading the chamber is no problem with...