nut

  1. P

    Gunsmithing Max profile for Savage barrel installed with nut.

    Hi all, I apologize if these have been asked already... What is the max profile (measurement?) for a barrel that can be installed on a Savage while keeping the barrel nut? If not using the barrel nut, I would assume the barrel profile can be bigger, and would install the same way as a...
    • pklin1297
    • Thread
    • barrel installed max nut profile savage
    • Replies: 15
    • Forum: The Armory
  2. Sumpter Steve

    Range Report "Nut" behind the rifle.

    Sometimes I get it right. This is a three shot group I did yesterday. It sure feels good when everything works as intended. Yes. I know I missed the little "black dot".
  3. RidgeRebel

    Gunsmithing RRA Lar 8 barrel nut

    Does anybody know who makes a free float hand guard with a barrel nut for a RRA LAR 8. I know DD makes one but I was wondering if that was the only option. Thank you for any advice you can give.
  4. Hogshooter

    Gunsmithing AR castle nut

    I have a Noveske lower on one of my AR carbines. Went to add a single point sling adapter to the lower and noticed that the castle nut is staked in the two notches to the end plate. I could not break it loose with my stock wrench so I took a small dremel bit to the staking. I am afraid to go to...
  5. eddy

    Gunsmithing AR10 Barrel Nut

    Is there a difference between the AR10 barrel nut and the SASS/AR10T barrel nut? If so, what else would change as far as a build would go? It would be going on an Armalite AR10 stripped upper. I searched through previous topics, but I couldn't find anything on the subject.
    • eddy
    • Thread
    • ar10 barrel nut
    • Replies: 8
    • Forum: The Armory
  6. patches

    KMW Cheek Mod Thumb Wheel or Wing Nut??

    Hey guys- Is anybody making a thumb wheel or wing nut like adjustment for a KMW cheek mod stock. I have a McMillan A5 with the KMW and I have to use an allen wrench to adjust the stock up and down. The problem is when I want to pull my bolt out of the rifle at the end of the day I have to put...
  7. Snafu12

    The Nut shooting AD needs to Go

    It is not what our sport is about It makes us look bad This web forum cannot be viewed in a public venue due to it It is offensive
  8. S

    Gunsmithing WTK: Castle nut torque - M4

    What does the tech manual say for the Castle nut torque on the buffer tube for an M4? THANKS
    • spr1
    • Thread
    • castle nut torque wtk
    • Replies: 7
    • Forum: The Armory
  9. R

    Gunsmithing Need help removing barrel nut

    Good morning! I cannot get the barrel nut on my rra ar to break free. I am using the dpms all in one tool. I have been told you can put a mag in the mag well then clamp that to a vise. I did, and all that happened was my mag got bent. I also placed the gun in a stuart gun vise to hold it...
  10. R

    Photos Savage Target Action W/O Barrel Nut

    Savage Target action trued and bolt timed, 30" MTU contour, 5R, Bartlein barrel installed without the barrel nut, all glass bead blasted.
  11. K

    Rifle Scopes Mounting rings: Screw/hex nut always on left?

    Since i spend so much time here, I noticed that everyone mounts their rings so that the screws (seekins) or hex nuts (everyone else) are on the right side of the rifle. So, thats how I mounted mine and figured, those hide guys know more than I. Anyway, I was at a friend's house yesterday and...
Top Bottom
Back
Home
Forums
Merch
Alerts