relaoding

  1. 6.5guys2

    22 arc reload data with 62gr eld-vt

    Ok guys and gals let’s hear what everyone’s reload data is looking like for the new 22 arc with the new 62gr eld/vt bullet. I know from my 20in proof it sure likes the factory and pushing them at about 3200fps.
  2. nightvisiondude721

    Reloading Equipment Retumbo and other powder

    2lb Retumbo: $60/lb 2lb us869: $35/lb 1lb H4831SC: $40/lb Prefer local sale in east valley, Phoenix area. All prices OBO
  3. TerribleProblem

    SOLD 6.5 Creedmoor Dies

    Hey guys. Looking to sell a few 6.5 Creedmoor dies as I no longer shoot the cartridge. #1 6.5 Creedmoor Micron Die by Bullet Central (will come with .290 Redding bushing) $200 TYD #2 6.5 Creedmoor L.E Wilson Sinclair MICRO-ADJUST BULLET SEATER $100 TYD Will sell both together for $275 TYD
  4. LongRange98

    Mk 248 Mod 0 help!

    Hello folks. I found a good deal of this Mk 248 Mod 0 190 grain smk for my .300 win mag custom bergara. However after doing some research it’s not clear to me if it’s safe to fire or not. I know Mod 1 is not recommended but not much info on the Mod 0. Can anyone help me out? Thanks!
  5. Mg427

    SOLD Dillon equipment, ammo case etc

    Dillion Powder Measure with toolhead and toolhead stand shipped $150 SOLD -Dillion 9mm Carbide Die set used shipped $40 SOLD -Dillion .45 ACP Carbide die set new sealed shipped $60 SOLD - Dillion Super Swage 600 shipped $ 100 All sold 1 Dillion primer flip tray shipped $30 2 RCBS ammo prep...
  6. Bunny723

    Christensen MPR 6.5 CM New barrel Brands???

    I’m looking for a new barrel for my Christensen MPR rifle chambered in 6.5 Creedmoor I’ve already worn out my factory barrel and would like to buy a different brand than what Christiansen offers from their website. ($875 for there carbon fiber/only option available). does anybody have any help...
  7. Tweetsounds

    Reloading Equipment Trade large rifle primers for small rifle primers, Tacoma Washington

    Looking to trade Federal large rifle primers (box of 1000) for small rifle primers (box of 1000). Located in Tacoma Washington.
  8. S

    Firing 308 win with only a primer

    Hello, After resizing some cases, I checked them out in my rifle and the bolt required some force to close down. Some of them require some force but close completely, and a few others just simply take too much force. I realized after that my lee die was not set properly and I needed to adjust...
  9. Evolution 9

    Reloading Equipment SOLD 30 caliber AP bullets

    I have either 100 or 98 (not counting them again 🤣) bullets for sale. I don’t reload so I’m offering them to someone who does. I recently saw some sell for more than this so I’m pretty sure I’m in the ballpark. 110 shipped to the lower 48.
  10. G

    6.5 creedmoor 22" 1-7 twist barrel, any opinion, experience or data?

    Hi guys, I'm planning about my next barrel, I'm going to always use direct thread Omega 300 for this gun. So wanna cut down the length and weight of the whole gun. (MDT ESS + Origin) Heard the new 150s heavy bullets are awesome, but need higher twist. So if I only use high BC bullets...
  11. S

    WTS: Once Fired Lapua Brass

    I have 100 once fired Lapua Brass in 338LM. The rifle that fired this brass was a Christensen arms TFM in 338LM. All brass came from the same lot. New lapua brass is $270 so I am asking 225. I am located in Montana if anyone is “local.”
  12. A

    Gunsmithing .223 reloading problems

    I recently purchased a Dillon Precision reloading bench and started to reload .223. I have had several feeding and ejecting problems with my AR-15, I had one bullet jam and several others be tough/ hard to extract rounds (im ejecting them by hand. "pulling the charging handle back"). I have...