reloads

  1. AIAW

    SOLD Inflection Magnum Ammo Case (5.50" Max OAL)

    For "Magnum cartriges" (300WM, 300NM, 338LM, etc). Brand new, never used. Uses a SKB 0907-6 I Series case. It has 50 holes to accommodate up to 50 rounds. MAX OAL of loaded round, 5.50" PayPal, Zelle or Venmo. $70 + $15 shipping
    • AIAW
    • Thread
    • ammo carrier ammo case ammo crate case inflection reloading reloads skb
    • Replies: 1
    • Forum: Buy - Sell - Trade
  2. A

    Reloading 223 mixed brass..

    Just getting into reloading. I have got the rock chucker press with some hornady bushing dies. I am going through my brass, guesing around 1,000 ish pieces. My brass is mixed. I have the following: Norma, LC, ADI, PMC, CBC, IMI, Winchester, Hornady. My queation is do i try and sell the brass...
  3. Metalhead0483

    First reloads through my .308

    Well I've had my .308 for about three months now and have been skating through on a case of Hornaday match ammo I got a smoking deal on. The rifle is an SPS tactical that I dropped in a B&C Light Tactical stock with a Bushnell 4200 6-24 tactical on top. With the Hornaday ammo my groups were...
  4. R

    Rate my Reloads.

    Finally got to shoot over a chrono a few days ago. Shot 20 rounds through the chrono and heres what I came up with. 45gns varget, 175SMK, FGMM Primers, out of a 26" remington barrel. About 103 degrees outside, no wind, 650ft elevation Lowest Velocity -- 2680.3 Highest Velocity -- 2710.4...
  5. C

    .223 reloads specifically 62gr m855

    Need your data and results for the following. load for 5.56/223 62gr m855 win or lc brass TIA!
  6. chadg

    Range Report ultramax reloads?

    Anyone ever tried ultramax 168 gr remanufactured ammo?Is it crap or would it be good practice ammo?Also if anyone has tried it are there any problems with swelled cases.
  7. RobG

    Couple of questions re: reloads in new chamber

    I am about ready to load up some rounds for my new 7mm. The once fired brass I resized fit nicely in the chamber, new brass is "loose" so I assume they will form when fired. Since the chamber is new and custom cut, I would like to load up some misc 140 gr and 160gr hunting bullets over listed...
  8. BgBmBoo

    NEW to relaoding..help for my 1st .223 reloads

    Hi Gang. I have never reloaded before...outside of shotshells about 25 years ago...and just set up my RCBS press. I was able to get my hands on 3000 CCI 400 primers some Hodgens Benchmark powder and some 50gr Sierra Blitz King bullets. Now I see in all the manuals I have looked at the...
  9. F

    Rifle Scopes Wonder optics scope and my first reloads

    Today I sighted in my new Wonder Optics 10x42. I used my first reloads. I recently bought a Lee classic loader for my FN pbr 308. Both the scope and the reloads shot great better than I had wished. Target sighted in at 100yrds My load 42.0 gr of Hodgon 168gr Nossler bthp federal brass 9 1/2...
  10. D

    R25 Trouble with reloads

    My new R25`s bolt will not close when loaded with a resized hand load. I have checked all the dimensions and they look fine. A factory Win. load works, as well as new virgin brass hand load. The reloads drop down into the chamber the same depth as a new one but the bolt wont fully close. My...
  11. Rancid Coolaid

    Peculiar problem with 300WM reloads

    I just bought a very nice 300WM and have noticed a peculiarity. When I fire factory ammo, the brass extracts and ejects without difficulty. When I shoot handloads through this gun (no signs of pressure on the cases, not shooting them hot, handloads are well within spec for case length and...
Top Bottom
Back
Home
Forums
Merch
Alerts