Accessories 5/8-24 Self Timing Muzzle Brake

[AznTactical]

Brand New take-off 5/8"-24tpi Self Timing Muzzle Brake that came off my Savage 110 Elite Precision 6.5 creedmoor. A little bit of cosmetic wear from my wrench when trying to remove it from my rifle. Even put duct tape on the wrench to prevent marring but failed. No loctite applied. I'm selling because I use SiCo muzzle brakes for my Omega suppressor. Will not work on .30 caliber+ rifles. Inside diameter of brake is Ø0.296".

$75 shipped

Trades:
Atlas Bipod Accessories
6.5 creedmoor 140gr or 147gr Hornady ELD-M bullets
SilencerCo ASR muzzle brake or flash hider
Magpul goodies
Berger 6.5 creedmoor 130gr Hybrid Target bullets
Underground Precision ELR bag
Walker's Electronic Ear protection

 

[Newbie2020]

What caliber is it?

 

[Newbie2020]

Also, what brand is it? Savage?

 

[AznTactical]

What caliber is it?

Edited. For 6.5 creedmoor or smaller diameter.

 

[AznTactical]

Also, what brand is it? Savage?

I spent at least 10 minutes researching on who makes it but could not find any info whatsoever.

 

[GrahamVT]

Short action like .308, 6.5 creedmoor, .243. I'm sure you could use it on .300 PRC and .300 win mag too. This brake comes on all factory Savage 110 Elite Precision short actions.

So its got a 30 cal hole?

 

[Newbie2020]

I assume you shot it on a 6.5 cm. Do you have any way to measure the muzzle opening? If it’s 30 caliber it will work on anything smaller. But I wanted to make sure.

 

[AznTactical]

I assume you shot it on a 6.5 cm. Do you have any way to measure the muzzle opening? If it’s 30 caliber it will work on anything smaller. But I wanted to make sure.

Sorry for the misinformation guys. It is for 6.5 creedmoor or smaller diameter caliber rifles. Hole as measured is Ø0.296". For comparison sake it was replaced by a 5/8-24 SilencerCo ASR muzzle brake which has a hole of Ø0.369".

 

[AznTactical]

.

 

[PA PYRO]

I've been researching for the last hour an a half how to get that off my gun like yours. Is the thing that crazy tight or is the front part a lock nut type deal? Want to put an EC tuner brake
on.

 

[acg]

Please tell me how did you remove it, my muzzle brake locking nut is already lose but brake it self doesn't move at all. I tried torch and no help.
Thanks

 

[acg]

I've been researching for the last hour an a half how to get that off my gun like yours. Is the thing that crazy tight or is the front part a lock nut type deal? Want to put an EC tuner brake
on.

Did you finally get it off?

 

[PA PYRO]

Did you finally get it off?

I did,,, I had to put the barrel in a barrel vise. It was definitely tight !
I couldn't get enough leverage to hold it tight enough.

 

[PA PYRO]

Please tell me how did you remove it, my muzzle brake locking nut is already lose but brake it self doesn't move at all. I tried torch and no help.
Thanks

 

[MilSpecOkie]

Those need a step cut in the barrel for the nut don’t they?

 

[PA PYRO]

Those need a step cut in the barrel for the nut don’t they?

The EC tuner brake doesn't

 

[MilSpecOkie]

The EC tuner brake doesn't

I was talking about the Savage brake being sold.

 

[PA PYRO]

I was talking about the Savage brake being sold.

I was talking about the Savage brake being sold.

Yes it does.
I thought you were talking about another tuner Eric has that requires a special cut .

 

[MilSpecOkie]

Nope. Just wanted to make sure any potential buyers were aware of this as it wasn't mentioned.