So, I am getting out of 6mm ARC. I have too many other projects going and lost interest. The barrel shot well (sub moa) but just have too much going on as I said.
Barrel- $185 shipped
Premium Series 20" Ballistic Advantage DMR profile 6mm ARC
7 twist, .750 gas block (rifle length)
416R SS
Nickel Boron M4 feed ramp extension
threaded 5/8-24
**Factory ammo fed fine at factory length. Did not have to shorten it as been reported by other 6 arc users
BCG-$90 shipped
PSA Nitride Bolt Carrier Group
9310 bolt, 8620 carrier
Properly staked, grade 8 fasteners
Dies- $50 shipped
Hornady FL set (sizer and seater) with Lee FCD, shell holder and Hornady modified case.
Bullets-$80 shipped
Nosler 6mm 105 RDF
2 boxes (1 full but opened) and the other has 85
Brass-I couldn't get any new brass at the time so all of it started from factory ammo (either black or match) $150 shipped
Hornady, 200 pieces. I would say the vast majority (80+% are 1x fired). I didn't do a lot of handloading, just shooting factory ammo to get brass and then never got around to using any of it.
Annealed, tumbled, sized, trimmed, chamfer/debur and primed with a CCI 450
11 pieces 2x fired and unprocessed (spent primer in place)
Ammo-SOLD
78 count 108 grain ELD M (2 full boxes, 40 rounds, are same lot #)
49 count 105 BTHP (Black) all are same lot #
SOLD
Target pictured is the only documented handloading session I have with the 105 RDF and one test load with the 70 grain Varmageddon. All shot from 100 yards, magazine fed and from prone using a bipod. The Varmageddon load chronographed at 3,096 ft/s and the others hovered around 2600 ft/s. All were shot with LeveRevolution powder. Everything is in very good condition and barrel was never shot rapidly. I will include a 5/8-24 thread protector that was on my RPR to protect it during shipment. With 211 pieces of brass and the 15 handload shots, I am estimating round count to be 226 rounds down the tube. Bore is bright and well taken care of and rifling is still sharp.
All prices OBO. Any questions, ask away!
Barrel- $185 shipped
Premium Series 20" Ballistic Advantage DMR profile 6mm ARC
7 twist, .750 gas block (rifle length)
416R SS
Nickel Boron M4 feed ramp extension
threaded 5/8-24
**Factory ammo fed fine at factory length. Did not have to shorten it as been reported by other 6 arc users
BCG-$90 shipped
PSA Nitride Bolt Carrier Group
9310 bolt, 8620 carrier
Properly staked, grade 8 fasteners
Dies- $50 shipped
Hornady FL set (sizer and seater) with Lee FCD, shell holder and Hornady modified case.
Bullets-$80 shipped
Nosler 6mm 105 RDF
2 boxes (1 full but opened) and the other has 85
Brass-I couldn't get any new brass at the time so all of it started from factory ammo (either black or match) $150 shipped
Hornady, 200 pieces. I would say the vast majority (80+% are 1x fired). I didn't do a lot of handloading, just shooting factory ammo to get brass and then never got around to using any of it.
Annealed, tumbled, sized, trimmed, chamfer/debur and primed with a CCI 450
11 pieces 2x fired and unprocessed (spent primer in place)
49 count 105 BTHP (Black) all are same lot #
SOLD
Target pictured is the only documented handloading session I have with the 105 RDF and one test load with the 70 grain Varmageddon. All shot from 100 yards, magazine fed and from prone using a bipod. The Varmageddon load chronographed at 3,096 ft/s and the others hovered around 2600 ft/s. All were shot with LeveRevolution powder. Everything is in very good condition and barrel was never shot rapidly. I will include a 5/8-24 thread protector that was on my RPR to protect it during shipment. With 211 pieces of brass and the 15 handload shots, I am estimating round count to be 226 rounds down the tube. Bore is bright and well taken care of and rifling is still sharp.
All prices OBO. Any questions, ask away!
Attachments
Last edited:
