New origin build

NJRaised

Sergeant of the Hide
Full Member
Minuteman
Feb 7, 2021
266
124
Port Murray NJ
Just wanted to say thanks for all the help with building this rifle. Lots of good guys on this forum. Getting to the range Monday and first competition later this month with it.

Origin SA
24” Proof 1:7 223 rem
Mpa comp chassis
TT diamond flat trigger
Vortex PMR rings 1.24”
Razor Gen 2
MDT AICS mags
Atlas CAL bipod w/ RRS BTC adapter
Threaded, no muzzle device yet.
 

Attachments

  • 186D75C4-BCA3-41A5-9E7B-AB3ECEFCA101.jpeg
    186D75C4-BCA3-41A5-9E7B-AB3ECEFCA101.jpeg
    476.6 KB · Views: 215
Looks like you went with Owen and had Garret do the chamber/muzzle work? Good luck at the Comp, hope that you do well.

TM6
 
Hit the range again today. I put some FGGM 69gr through it, eight x 5 round groups, biggest was a .7” spread. Average was a .5”

Started shooting 75gr hornady BTHP, and this was the result, 5 shot group.

Still working on getting some feeding issues resolved. Ordered up some accurate mags, aics pattern.
 

Attachments

  • 7EB8C439-0047-434C-9188-2920EE1C8924.jpeg
    7EB8C439-0047-434C-9188-2920EE1C8924.jpeg
    686.2 KB · Views: 59
Hit the range again today. I put some FGGM 69gr through it, eight x 5 round groups, biggest was a .7” spread. Average was a .5”

Started shooting 75gr hornady BTHP, and this was the result, 5 shot group.

Still working on getting some feeding issues resolved. Ordered up some accurate mags, aics pattern.
That thing is a hammer. Care to share your load?
 
I had the same issue with my mdt poly magazines in my MPA chassis.
The fix was adjusting the mag latch higher so the magazine sits closer to the action, give it a shot its really easy to do amd it's free.
I tried this. I have it adjusted all the way up, and it’s still giving me an issue.

I have it set right now all the way up, and then sanded the feed lips down as thin as possible so that the bolt had clearance to pass the magazine. It feeds but still requires a lot of effort. It also feels like the action is functioning as a “push feed” rather than the round sliding under the extractor.
 
I tried this. I have it adjusted all the way up, and it’s still giving me an issue.

I have it set right now all the way up, and then sanded the feed lips down as thin as possible so that the bolt had clearance to pass the magazine. It feeds but still requires a lot of effort. It also feels like the action is functioning as a “push feed” rather than the round sliding under the extractor.
Damn, that's a bummer. Hopefully a different magazine does the trick.
 
Nothing. Working up the charge slowly.

Cool was just wondering as I have friends that use N135 and 75 ELDs getting 2930fps in 26" barrels. I have some N135 on order but could change to N140 if it seemed to work better but from all my looking around it seems N135 is favored by a little for 75s. Seems like you can't go wrong with either and their burn rates which are close to other known good powders.
 
Last edited:
Cool was just wondering as I have friends that use N135 and 75 ELDs getting 2930fps in 26" barrels. I have some N135 on order but could change to N140 if it seemed to work better but from all my looking around it seems N135 is favored by a little for 75s. Seems like you can't go wrong with either and their burn rates which are close to other known good powders.
I’m gonna work up the powder slowly. I’m a newbie to the reloading game, so I’m being cautious to start. Enjoying it though!
 
  • Like
Reactions: Rob01
I’m gonna work up the powder slowly. I’m a newbie to the reloading game, so I’m being cautious to start. Enjoying it though!
I may have hugged a tree with my first round after I started loading 🤣

Guy got in my head asking me 1000 questions, I said fuck it I'm putting a tree between me and the shit first round.
 
I’m gonna work up the powder slowly. I’m a newbie to the reloading game, so I’m being cautious to start. Enjoying it though!
Always good to be cautious. I wasn’t trying to push you but just trying to get some info on a powder I haven’t used.
 
Accurate mags for the win. Solved all my problems .
This is great info for me - I have an Origin and 223 prefit inbound and still deciding on chassis (either KRG W3 or MPA BA comp) and have come across some having mag issues, at least w/ the MPA. For my other calibers I use MDT metal mags that work great, but its helpful to hear that the Accurate Mags are the way to go with the MPA chassis.
 
This is great info for me - I have an Origin and 223 prefit inbound and still deciding on chassis (either KRG W3 or MPA BA comp) and have come across some having mag issues, at least w/ the MPA. For my other calibers I use MDT metal mags that work great, but its helpful to hear that the Accurate Mags are the way to go with the MPA chassis.
I have a w3 on my tl3 it’s my favorite chassis and action the chassis is just super comfortable and easy to get behind and the mag well is adjustable a little bit
 
  • Like
Reactions: Travis T