Sizing lube removal

Kyskeet

Private
Full Member
Minuteman
Feb 22, 2017
181
54
i currently wet tumble, dry in dehydrator, anneal, spray lube, resize, if small batch I spray with alcohol and wipe to remove lube. What is your preferred method to remove lube from say 100 pieces.
 
Same here. What spray lube you using? Hornady One Shot doesn't technically need to be removed but I still toss it in the tumbler for 15-30 minutes.
 
I am using 10% lanolin in 99% alcohol. Seems I read on line that lube
left on cases would result in excessive bolt pressure
 
Last edited:
Have never intentionally removed lube after resizing in 30+ years reloading handgun or rifle. Reload rifle from 22Hornet, 223, 7-08, 243, 270, 6.8SPC, 308, 300WinMag, 300WSM, 375H&H, 416 Rigby, 7Rem, 284Win,etc. Guess I have been doing it wrong.
 
I never take it off. Never been an issue in 25 years of loading everything. I only bump the shoulder about .002 and use a bushing to size the neck about .002 so i don't use much lube. Most I ever do is roll them around in a hand towel if that.
 
For the guys that tumble in dry media - what do you do about media stuck in the flash hole? Ive been doing ultrasonic after sizing but then i have to wait until the cases are dry before loading, so that means I dont load until the day after I size. Normally this is fine but there are times when I want to just run striaght through sizing then loading. But the flash hole thing bugs me


Sent from my iPhone using Tapatalk
 
For the guys that tumble in dry media - what do you do about media stuck in the flash hole? Ive been doing ultrasonic after sizing but then i have to wait until the cases are dry before loading, so that means I dont load until the day after I size. Normally this is fine but there are times when I want to just run striaght through sizing then loading. But the flash hole thing bugs me


Sent from my iPhone using Tapatalk

I use a media separator and most of the time I don't have a problem with the flash hole. When I do, maybe 5-10 out of 100, I pop it out with a toothpick.


Sent from my iPhone using Tapatalk
 
I spray mine down with rubbing alcohol and wipe down. I'll dump them over. Towel and spray them down. Roll them around a bit and spray them some more making sure I get them good. Fold the towel over itself and rub them out. Has worked great and never had any issues. Very fast and effective.


Sent from my iPhone using Tapatalk
 
For the guys that tumble in dry media - what do you do about media stuck in the flash hole? Ive been doing ultrasonic after sizing but then i have to wait until the cases are dry before loading, so that means I dont load until the day after I size. Normally this is fine but there are times when I want to just run striaght through sizing then loading. But the flash hole thing bugs me

I process on a DIllon 550 using two toolheads, one for brass prep and one for loading, tumble in between to clean off the lube. I use a depriming die in station one on both toolheads so the flash hole is cleared automatically and I don't need to check it.
 
I load progressively on a Dillon RL550B, using RCBS Water Soluble Lube, As I pick up and insert the case into the resizing/decapping/recapping station I wipe the sidewalls with my fingers dampened with the lube.

When the progressive reloading process is complete for the batch, I remove the cartridges from the hopper individually and wipe each one down with a shop cloth that's been well dampened in 90% rubbing alcohol just before inserting it into the cartridge box. This removes the lube, any slight lingering carbon on the case neck, and any fingerprints that may have also been deposited. The ammunition ends up looking like new factory manufactured cartridges.

I follow this up by removing the decapping rod/resizer ball, flipping the toolhead over, and scrubbing out the dies with a light alcohol/preservative oil mix on a chamber mop. As the alcohol evaporates, it leaves behind a very light film of oil on the die interior, helping to prevent oxidation. A final wipe of the decapper rod with the alcohol cloth, reassembly, and the toolhead is ready for further service.

I am the second(?) owner of this press that I bought in the early 1990's. Faithful cleaning, lubrication, and readjustment keeps it running, so far, indefinitely. I make it a regular step in my reloading sequence

Greg
 
Last edited:
I tumble with corn cob but I also use the addition of pieces of a old washcloth cut into aprox 2" by 2" squares. About 6 pieces for the larger Dillon tumbler. I wet all the squares and toss them in. Tumble for 30-45 minutes. if it didn't do something, they wouldn't be black when they come out.