Accessories WTS McMillan A4 and A3? for FN SPR / Winchester

[Waorani]

The SPR thread got me digging through old stocks that I'll probably never use.

SOLD McMillan A4 - bought from someone here a few years ago. Seller had sent it back to McMillan for a "desert camo" repaint. Overall very good condition, couple of minor scuffs/marks from storage and has been bedded. The cheek rest knobs are rusted on the knurled edges and inside surface. McMillan doesn't have but I'll order a set from McMaster Carr. 6 QD cups - 3 front and 3 rear. $375 shipped - PP f/f, USPS MO, check.



I believe this one is an A3. Also bought used from someone here. Overall good condition but has some scattered red speckles in finish. I believe it's the gel coat showing through on high texture spots that paint has worn a bit. Was also bedded at the lug and rear tang. Rear sling swivel was missing when I took pics but has been replaced. $350 shipped - PP f/f, USPS MO, check.



Both are short actions and inlet for TBM/similar footprint bottom metal.

 

[Jcarrick]

Interested A4

 

[Jcarrick]

I’ll take A4

 

[Waorani]

I think buyer was confused about A4 and I haven't heard from him in 24hrs so A4 is still available. Ordered the replacement thumb screws today and should have in hand tomorrow.

 

[Jcarrick]

Pass, apologies for the confusion

 

[stello1001]

Someone buy this, Waorani is a great seller. I purchased an A3G for my SPR and it arrived in great condition. Fast shipping too and excellent communication!!!

 

[TheFlyingNerd]

Do you know what bottom metal the A4 is inletted for?

 

[Waorani]

Both are inlet for FN TBM/Winchester M70 wide mouth DBM (not included). Someone else asked about barrel channel - not sure on contour name but straight & 1.17" at end.

 

[kcgrendel]

What’s the barrel channel on the A3?

 

[Waorani]

What’s the barrel channel on the A3?

I'll check when I get home this afternoon.

 

[Waorani]

Ok, upon closer inspection, both barrel channels are very slightly tapered. Widths just in front of lug and at end:

A4 - 1.30 & 1.18
A3 - 1.29 & 1.19

Kind of hard to measure consistently given curves, texture, how you place calipers, etc but this should be pretty dang close.

 

[Waorani]

Bump

 

[yej0001]

A rare bird A4 stock for an “FBI sniper rifle” project.

 

[Waorani]

Bump

 

[Waorani]

Found a brand new set of original McMillan cheek rest screws I forgot I had for the A4.

 

[Waorani]

Yep!

 

[Waorani]

Last bump. Guess I'll just stick 'em back in the closet.

 

[USNavy06]

Just wanted to double check but you did get a new set of screws for the a4 right? If so I’d be interested

 

[Waorani]

Just wanted to double check but you did get a new set of screws for the a4 right? If so I’d be interested

Yes, I found a set I must have ordered from McMillan at some point.

 

[Deej]

A4 still available?

 

[Waorani]

A4 still available?

Yes

 

[Deej]

I will take it.

 

[Waorani]

A4 - SOLD

 

[AccuSol-ERN]

I call seconds on the A4 if the deal falls through.

Ern

 

[Waorani]

A4 - sold and shipping today.

A3 still available.