I have a Seekins Havak Hit with the quick change barrels and bolt heads. I wanted a 6.5 PRC Seekins barrel but they are OOS, but I do have a 6.5 CM barrel for it. Can a 6.5 CM barrel be rechambered to 6.5 PRC without being set back? If all I had to do is have my gunsmith run a PRC reamer in it that would be awesome.

Picked up an Arken LH4, 4-16 with MIL based VPR reticle.

This model has capped turrets (nice for hunting), and the elevation turret has been redesigned so you don't have to worry about the set screws backing out.

Mounted in a set of Arken 30mm rings but hasn't been used.

$270 shipped with rings

Its almost that time of year when funcle Doc sends the guys some Christ-mass gifts.

This summer they spent the evenings watching some movies I thought were appropriate. Some of the tag lines upset their mama when they wouldn’t quit.

I think the one they enjoyed most were:
-Sandlot
-Rookie of the Year
-Little Rascals
-Little Giants

Pretty much any kind of “little boy” film where they could see themselves as the characters.

Oh wise Sage of the BearPit, I come to you again seeking knowledge, what “KID THEMED” films should I introduce next?

Leica 3500.com CRF Rangefinder. Unit functions 100%, comes with original box, literature, arca plate, housing and RRS 1/4X20 ballhead. $700 shipped or trade for a set of Peltors, Kestrel 5700 Elite, or AMPS (+$ on my end)

Douglas 16" 1-7 SPR barrel with AEM 5 collar/brake, Aero Enhanced FDE Upper, BCM QRF 12 FDE (was black kryloned but stripped off), new BCM charging handle, unknown BCG (believe it is a BCM or aero that is unmarked).

No tape switch or arisaka thumb stop.

Barrel easily shoots sub MOA and has about 550-700 rounds on it. Runs great with 77SMK and 8208. It also shoots well with the AAC 77 gr TMK. I took it out to 670 with it.

SOLD shipped. Photo of the full rifle attached with an OCM5 on it for posterity. Built it before knowing what an NSW Recce was.

I have 2 barrels for sale. One is the factory Q 6.5 creedmoor. It came on my rifle and I swapped it out. Never fired that I know of. No cherry bomb on it. I think these are 1-8. Asking $375 shipped.

Next is a brand new in the box 6 creedmoor proof carbon barrel with the extension. 1-7.5 and is 18”. Super lightweight. I bought it and moved away from 6 creedmoor. I paid about $950 for it. Asking $775 shipped.

PM me any offers. I accept PP, Zelle Venmo etc.

Thanks.

I have a pair of Revic BLR10b's looking for a new home. Used these for NRL Hunter matches last year. No issues. Worked extremely well. I'm trying out the new Vector X's, and can't afford to keep both.

Ships in original packaging with all parts included.

$2,000 shipped

No trades at this time please. Thank you.

Figured I'd post something gun related for a change.

This is one of Kenny's in house barrels that is cerakoted black and cut for a Rim x. It's 1.2 straight, 23" long and 1:16 twist. Muzzle is not threaded per Kenny it isn't needed and he was right. The barrel has around 2000 to 2500 rounds through it.
The only reason this barrel is available is because my son has another gunsmith helping him in his shooting journey so his brand is all we will be using. The pic below is a dot drill my son shot at 80yds changing positions after each shot. $600

Vortex Strike Eagle 5-25x56 MRAD
Excellent condition and lightly used on a 223. Tracked well, got hits on 1230yd plate.
Great scope that pretty much is as new with all literature and accessories.

I'll take $550 Shipped tyd

Have one Black NIB Kestrel 5700 AB with Link that needs a home.

$735 Shipped

Okay, I'm not a child but the more I try to find answers, the more confused I get. I'm looking at the new Sig Kilo6K LRF binos. I'd like to have some manner of getting my DOPE on a watch. I'd prefer someothing that can be worn everyday and not something that looks like an arm board so the Instinct looks like a good candidate. I can live with getting one target at a time as I'm not a competition kinda guy.

But what exactly do I need? How do the watch, my phone and the binos interact? What app will I need to pay for to unlock ranges beyond 800 yards?

Specifically, can I get an app on my phone, enter my gun data and bluetooth it to the watch? Once it is in there, will ranging a target with the binos show my range and drop?

For Sale is a lightly used Send It Level and a new in the package (never used) Long Range Arms mounting bracket for a Spuhr mount.

Pricing (please note I will not separate the items at this time): $215.00 delivered to the lower 48 via USPS Ground shipping.

Payment terms: USPS Money Order
- Note: items will ship immediately once the payment arrives.

Please PM for additional information or serious offers.
Thank you!

ATS original tuner 5/8x24 threads - $make offer

Black Collar Arms pork sword savage small shank 300blk barrel and nut. approximately 80 rounds through it. Yes, I like it, but want the action for another project and can't afford another action. The pic is to show the length in a MDT LSS chassis. The chassis can also be included with discussion. Just the barrel and nut are - $275 shipped

I can send more pic if needed or vid chat.

Venmo or PayPal G&S.

This dude is a riot.Did you see him being asked if there was a way to deport illegals without separating families?"Of course there is families can be deported together" LOL its going to be a fun 4 years. These libs are going to be urinating blood by the time this is over.

Selling for a friend of mine. Like the title says, Laugo Alien 9mm handgun for sale. This gun is about 2 years old and only has about 500 rounds through it. This guy is former military and he cleans and maintains his firearm at a level above pretty anyone else I know. Here's what you get.

Laugo Arms Alien Pistol
Large Custom Hard Case
Three (3) 17-round Magazines
Magazine Well
Fiber Optic Iron Sight Top Rail
Optic Top Rail w/ Laugo Red Dot Optic (6 moa)
Elornis Industries Holster & Mount
Cleaning Supplies

Looking to get $3750 shipped to your FFL, insurance is on the buyer. All state and local laws apply.

No trades please.

PayPal F&F preferred, additional photos a information available on request.

PM with any questions.

CM

Senator Cornyn now states he defintetly wats to see ethics report on Matt Gatez. I am betting he doesnt pass the nomination cause of this guy Cornyn,Collins ,Murtowski and probably McConnell too.Plus every Dem will vote no.

Hello, everyone. I'm working on a 1984 Winchester Model 70 and the safety lever is stuck in the Fire position while the bolt is in the rifle. It's not crud or gunk. It is a mechanical stoppage. In the Fire position, the trigger cocks and fires. When I remove the bolt from the action and manually cock the cocking piece, the safety lever works just fine. I've taken the bolt apart and pulled out everything. I have examined the safety cam lobe and the cutout on the firing pin and have found no burrs. The part of the sear that makes contact with the cocking piece appears to be fine as well.
Backstory: This rifle came to me in parts so I have no idea if it worked before it was brought to me. The owner doesn't know if it worked prior to bringing it to me either. After bluing I have reassembled everything including the trigger which I set to four pounds. This is a real head-scratcher so any insight would be very welcome. If pictures would help, I'm happy to provide them. Thanks.

Brand new in the box TT 5-25x56 with jtac reticle. Only opened to finger, never been mounted or outside the house. I can take more pictures if needed.

$4500 shipped and insured.

Barely used Streamlight TLR1 HL long gun kit. Comes with standard switch and a new dual switch for running with a laser (Crane plug). Also a monstrum scope cover. $140 Paypal FF. Shipping CONUS included.

I have 3D-printed parts available for the Vudoo V22. These are all things that I made for myself and use them with my Vudoo, but then other Vudoo shooters at local matches wanted some too. I’m making them available to our ‘Hide members here. Most items are made to order, so you can pick your colors and/or options.... If you're like me and color doesn't really matter, I'll just pick it out for you based on what I have already made or the filament I've got loaded in the 3D printer. If you're not familiar with 3D print items, they're made layer-by-layer by melting plastic filament through a 3D printer, and may have cosmetic imperfections (layers visible, etc), but I guarantee that they'll do the job they're designed to do!

I combine shipping... you basically pay $4-5 shipping (sorry, had to raise it) on just your first item and the rest going into the same package are discounted.

1. Single-shot Adapter: For F-Class and other matches that require single-shot loading, or just because you prefer it, I have a lightweight magwell insert/adapter that is topped with a "sled" for loading a single round at a time. As I'm sure you've seen on your gun, there's not much exposed room in a repeater action when the bolt is open, but the "sled" is as big as possible while still clearing the bolt surfaces and putting the bullet at the correct angle so that the bolt pushes it smoothly into the chamber. If your fingers aren't thin or as nimble as they used to be, consider the "single-cartridge 'pen' holder" below to use with this. I most commonly make these adapters in yellow or white (makes it obvious to the match director that you're not using a standard magazine), but can be 3D-printed in gray, or black on request. NEW: As a special request by a shooter that uses a joystick front rest where the joystick hits their magazines (and so also a normal single-shot adapter), I have developed a "compact" (short profile) version that sits almost flush with the bottom of your rifle stock, with just enough exposed to grab to seat or remove (see image of model below). If you don't specify this "compact" version specifically, though, you'll get the regular, magazine-sized version. Either version is $25 shipped.

2. A single-cartridge "pen" holder-- a rod type tool that holds one 22 cartridge slip-fit by the base that you can use along with (or without) the single-shot sled to aid in inserting a single cartridge -- great for cold days, gloved hands, or just less-than-nimble or pudgy fingers. I made this so that I never "miss" when putting a cartridge in place on the single-shot adapter. I use this same tool in combination with single-shot adapters with my CZ and Anschutz too. You slip the back of a cartridge into it (see photo) and then start the cartridge into the chamber, easily pull the holder away and then simply use the bolt to finish seating the cartridge into the chamber. $4 when shipped with a single-shot adapter or also add $5 for mailing if ordered alone. I usually have them pre-made in white or yellow or gray.

3. A V22 bolt assembly/disassembly/cocking/decocking/recocking tool, similar to the one offered by Vudoo Gun Works. If you ever over-rotate your bolt and the cocking piece ends up in the cocking ramp (you've just accidently de-cocked your bolt), this tool also EASILY allows you to move it back to normal cocked position in about 2 seconds without *any* disassembly so you can slip your bolt back into your gun. $22 shipped, or $18 if you're already paying shipping on another item being mailed at the same time. This tool works on V22 repeater bolts *and* V22s single-shot bolts. I guarantee that this works as described, and that it works just like the more expensive version available direct from VGW. I most commonly make these in white, yellow or orange (easy to find in your range bag or your tool kit), but can also be made in red, black or gray.

4. A thumb-assist magazine loader for V22 repeater magazines. These work on both polymer and metal type magazines, but if you buy metal mags from Vudoo, they all come with a gadget like this anyway. Especially for us polymer mag owners, if you have trouble pulling down on the magazine follower spring buttons "just right" to avoid rim-lock, then this tool is for you. It gives you just the right depth before you drop in the next cartridge. This is also really helpful if you use replacement magazine extended baseplates for 12 or more cartridges such that you've had to remove the load-assist buttons. Another use: if you have a polymer magazine that is a little "tight" at the top and that first round doesn't freely drop when you pull down on the spring assist buttons, this gadget will overcome that easily. I most often make these in orange, yellow, or white (easy to find in your range bag) but also can be made in black or gray. $14 shipped, or $10 if you're already paying shipping on another item being mailed at the same time.

5. V22 Magazine Caps -- if you like to pre-load your magazines before going to the range like I do, these slip-on/snap-in caps protect that exposed top cartridge from bullet damage. They only work on at least partially loaded magazines (otherwise on a fully empty magazine the follower buttons get in the way). Unless you state otherwise, you'll get them sized for Vudoo's polymer magazines, but slightly different ones for the Vudoo metal mags are available on request. Available in translucent clear (which is what I like to use), white, yellow, black, or gray. $8 for five, $15 for ten, including shipping with any other item. If ordered alone, add $5 for shipping for up to quantity 15. Because of the "fingers" that hold them on, they can break if banged around a bit, so you might want to order extras... but I personally have six magazines with these covers, and in the last year and a half have only had to replace one cover.

6. V22 Magazine Bench Tray -- Holds five Vudoo polymer magazines (with or without mag base extensions) on the bench to keep you (me) organized during a match. The mags sit at a tilt, ready to grab, but the slots are not tight so there's no fumbling. This is ONLY made in GRAY or BLACK. It can be produced personalized with your name molded into both sides for $5 more, otherwise text will be "VUDOO". $30 shipped (uses a lot of plastic and takes over 15 hours to 3D print!). Sorry, this is one of the few of my items that doesn't benefit from combined shipping since it usually has to go in a separate package.

7. V22 "Plus 1" Magazine Extension -- Replaces baseplate on the V22 *polymer* magazines to allow an extra round (11 total). I personally run these on my mags -- treating one as a "spare" just in case. These also have numbers 1 through 6 on the bottom with a corresponding dimple in which you can put a dab of paint or fingernail polish if you like to keep your magazines individually identified. I usually keep some on the shelf made in gray or black. $10 each, $45 for five. Add $5 shipping if you are not combining with other items. NOTE: Some of the photos show taller "Plus 2" type extensions. I'm currently making just the lower profile "Plus 1" extensions, same as I personally use.

7A. V22 Magazine Base Inserts -- You know that sinking feeling in your stomach when you've taken apart one of your magazines and that little insert that goes at the bottom of the spring and into the magazine base goes flying? Yeah, me too. I've never quite lost one yet, but I've come close, so I've made spares for just such an emergency. I made mine in orange (easier to find on the floor) which will also be the color you get unless you specify otherwise... I'm also keeping packs of dark gray on the shelf, and I have a couple sets here of dark gray with red buttons. Choices per pack of 3 are orange, gray, yellow, or black. Of course, when they're installed in a magazine, all you see is the small round button you depress for disassembly. Sold as a pack of three for $10, for peace of mind. Want them in different colors for magazine differentiation? Pack of three in mixed colors (your choices for each one in a different color: orange, yellow, dark blue, royal blue, cyan, green, red, white, gray, or black) for $18, or pack of five for $25. Add $5 for mailing if you are not combining with other items.

8. V22 Trigger Spacers -- If you're going to send your V22 barreled action to Lapua or Killough/Eley for ammo testing, be very careful with your trigger so it doesn't get damaged in shipping. What I did was make two spacers (sort of like stock bedding pillars) to hold the trigger guard/base metal in place to protect my actual TriggerTech Diamond trigger assembly while my barreled action was out of the stock and being transported. Of course you can get something similar from the hardware store, but if you want these, they're the correct diameter and length and $2 for the pair. Add $4 shipping if you are not combining with other items.

9. Chamber/Safety Block -- If you don't like the idea of putting a plastic safety flag in your hot chamber, this is for you. Typically made in bright yellow, orange or red, this is similar to the single-shot adapter, but without the sled, and instead visibly blocks the chamber as a safety device with the bolt open or removed. $20, and add $5 shipping if you are not combining with other items.

10. Bullet Bench Tray -- If you're shooting a match with a V22-S or otherwise need to feed single-shot, I made this tray with the cartridges in 5-shot sets. It holds 60 rounds in the twelve 5-shot sets, plus an extra 2+2 in the middle, all in a pattern that makes it easy to for you to progressively remove individual cartridges and to tell at a glance how many you've shot (how many have been taken out of the tray). It's intended to sit on the bench with you (or on your shooting mat if you're prone and/or doing F-Class), and is 4" x 6.5" in size. It's smooth on the bottom (that's the way I use mine), but you can add a length of adhesive neoprene strip or similar to the bottom if you want it to be less slick on your bench or mat surface. $30 shipped (uses a lot of plastic and takes almost 12 hours to 3D print!). Sorry, this is one of the few of my items that don't benefit from combined shipping since it usually has to go in a separate package.

11. Bullet Cartridge Tray "Lifter Boxes" for Lapua, SK, RWS, and Eley... and now also CCI Std Velocity and Norma TAC-22 -- My old fingers have trouble getting the cartridges out of the Lapua or SK boxes one-by-one to load into magazines or to take out and put in a bench tray for single shot feed. The lube can be messy so I don't like to just dump them out, so I've made a simple fixture that you put the 50-round tray in right out of the box, and it raises the shells up -- with the rows in alternating heights -- to make them easy to grab without having to pry them up with my fingernails. Not a big deal, but takes care of a small annoyance. The staggered rows are tall enough so that you can use it for single-shot direct loading if you don't have another block to use like my one in #10. I prefer these most of the time since they don't require transferring the cartridges to another loading block. The Lapua and SK box trays are identical in size so both will work in the same fixture. The RWS box insert is larger so it has its own version (the Lapua/SK trays can fit in the RWS fixture, but they're quite loose and better in their properly-sized fixture). What I've done is "tailor-made" each style for that specific manufacturer. Eley ammo boxes don't have these kinds of trays, but have a flat rectangular panel that you have to pop out of their box... I have a version of the lifter that you can drop in and put the panel back on the original box, and easily take it back out when you're done. This works with Eley's flip-top boxes (Match/black box, Club, Contact, Force, etc) and their slide-out type box (Tenex). I also have a version for Eley that is more like the Lapua and CCI Std Vel trays, where you take the top panel out and lay it in the tray. I personally prefer the drop-in insert when using Eley, but it's a personal preference. If you use CCI Std Velocity or Norma TAC-22 for practice/plinking ammo, I have versions for them too! All the above versions are $13 each. Add $5 shipping if you're not combining with any other items, but that $5 will cover as many as SIX of the lifter boxes in one package. NEW: For match shooters in high-heat environments where you have to be in the direct sun while shooting, or have to store these in a hot car, heat-resistant versions are available. I'm in Alabama -- summers are HOT here, and I've never had a problem with the standard ones, but I've had just a couple reports from New Mexico and Florida where they've warped a bit when they've gotten too hot... only the Lapua/SK and the RWS styles. These heat-resistant ones are 3D-printed out of a translucent PETG instead of the usual PLA material. They take twice as long to print, so I have to charge a little extra for them ($18 each instead of $13)... but they're available if you need them. I keep the heat-resistant Lapua/SK and RWS versions on the shelf, but I can make them for any of the other brands listed.

Looks like Rick Scott got kicked out on the 1st Ballot.

Well I Hope Pres. Trump (or his sons) can "incentivize" Thune to get some of Trump's legislation through. Especially the 2A stuff.

And, At least we here in FL don't have two Senators to replace. I've been hearing rumours about Lara Trump replacing Rubio. That would be really nice, but we'll see.

Proof comp prefit for Big Horn origin. Chambered in 6 creedmoor, around 300 rounds. $400

I have I have a 22 creedmoor 3 dies set. Includes Redding FL/Neck bushing dies, RCBS Competition seating dies and neck only sizing die.

I will include 5 Short Action Customs neck Bushings - .247-.251

Looking for $215 shipped. Bushings alone will run ya $200.

Hey all,

I want to do a chopped 20S project, 15"-16" barrel length or so, in .308
Is the 1:12 twist okay for this barrel length and this caliber? I would like the gun to be optimized for 168-175 grain projectiles.

Thanks!