Action has 1200 rounds on it so it’s smooth as butter. Barrel has 110 rounds on it. Shoots FGMM lights out.

- MPA marked Curtis vector 3-lug SA.
- Bartlein 1.25” straight, 26”, 1:7.5 spun up by MPA. Threaded 5/8x24.
- triggertech primary. Can swap it out for a elfmann for $100 more.
- APA fat bastard Gen 3

$1,400 shipped

Like the title says. If you are using the Hornady HiT hit indicators, how are you attaching them to the posts/targets?

I have 2 v3 magnetospeeds with a mount ill double check which mount system it is when I get home on Monday one of the bayonets doesn't work due to a bullet strike but the other one works perfectly. Asking 150 for both of them.

Price is shipped. PP F&F or Venmoe. You cover fees if using G&S. Offered in lower 48 excluding Alaska and Hawaii

SOLD - 1 - Zermatt Action Wrench for TL3, SR3, Origin and RimX. $65.00

2 - NF 20 MOA base for LA 700. $55.00

SOLD - 3 - Stainless 700 SA BDL complete bottom metal with action screws $125.00

4 - Remington 700 SA ADL trigger guard and box mag / follower $60.00

Loading Lapua Brass with 105 bergers and H4350. Started at 38g and wound up with pressure signs right away at 38.5/39. Any recommendations?

Looks like the next rifle is going to be a 6 Creedmoor instead of the 6.5 Creedmoor... Looking for some load details from you guys that are already running it...

Now I have to figure out what I'm going to do with all these loaded 6.5 Creedmoor factory loads I have sitting here... Maye time to start pulling bullets.

Back when I was taught how to mount scopes, I had to have a way to torque screws correctly. I saw ads for the Wheeler torque screwdriver, but I also saw unfavorable reviews. I was afraid a torque screwdriver that cheap would fall apart. Torque screwdrivers from industrial-tool companies can cost over $300, so I figured there might be a reason.

I got myself a beam torque wrench instead, and I used a 1/4" magnetic socket to hold bits. Has anyone else tried this? It seems to work just fine, it was cheap, it never has to be adjusted, and it should last forever.

The other day I found a used Sturtevant-Richmont driver for $43, so I grabbed it. Easier to stow than the beam job.

At least it's a mystery to me! Ar15 300 blkout, bolt doesn't lock on last round. I know this can be a common problem but the issue I'm having is it doesn't do it on all ammo. My last trip to the range I fired 25 rounds each of Fiocchi Range Dynamic 150 gn, Remington 200 gn. and my reloads of 15 gn. of H110. The Fiocchi load, eject fine about 4:00 oclock as all of round do but didn't lock the bolt back same as the Remingtons although I had one failure to eject as it tried to feed the next round and it locked the bolt once out of 25 rounds. My reloads, load, fire, eject and lock the bolt every time including a prior trip the range when I fired only my reloads. My reloads are very close to the Fiocchis in bullet type and FPS should also be very close based on published numbers have not chronoed them. The only difference that I can think of is my reloads have a longer C.O.L, Any ideas? Thanks in advance.

Had this for 2 years, always kept in protective cover. Didn't use it much. Comes with phoneskope adapter.

$1500 + actual shipping or face to face in north Idaho. Paypal F&F or Zelle.

Manners stock w/adjustable cheek piece

Anarchy bottom metal w/action screws

Area 419 weighted arcade rail

Safety flag.

$850.00 shipped

30 Cal Hellfire Match, used while waiting for my 6.5 match to show up probably 40 rounds through it. The adapter is 5/8x24 and is new.

$130 firm shipped

Looking for a couple TL3 223 bolt heads and 223 barrels. Prefer barrels to be new. Send me a PM with what you have.

I am looking for 1 more. Looking for a new Proof steel 223 prefit. Can be for origin or TL3.

Front Range isn't showing any in stock.

I have a 26in bartlein 1-7.5 twist chambered in 6 Creed on a impact 737. It was a great shooter with around 0.3 moa groups and SD's around 4 for at 2945 fps for about 600 round. Since then I have a big increases in velocity with about every 80 - 100 rounds. It will just anywhere from 35 to 40 fps and my SD's have slowly moved up to around 11. Now my velocities are up around 3080 fps and if i try to change my load at all i get pressure signs even though i am near a minimum charge of powder. Also I have to rezero every couple of weeks. My groups are still around 0.5 moa at 100 yards. I have tried different brass and powder and primers with no change. I have close to 1600 rounds on this barrel. I am wondering if I should pull it off and get a new barrel. My buddy has the same spec barrel as me on a impact and his will shoot lights out with what ever he throws in it. If someone has a recommendation for something else please let me know.

Sig 320 x5 max
1100obo takes it all

4 17rd mags with henning +6mag extension

2 17s with Taran extension

1 21rd

Springer precision tungsten guide rod

Springer precision extended mag release

Gray guns grip module

Gray guns trigger

Double alpha belt size 38

Cr speed mag holders

Ghost hydra P holster

Stoger boss hanger

Was used solely as a uspsa gun for 5 matches

Everything is carry optics legal

Full match spot available that includes the train up day.
Squadding opens tomorrow so get it now before you miss getting to shoot with your buddies

This is cross posted and FCFS, no holds
$375 is what I paid
PayPal, Zelle, or Venmo as last resort

Mint 16" A4. I had the trigger replaced with a compatible wilson two stage match trigger, Geissele rail installed (original is gone) and had D wilson profesisonally cut out a pocket to adjust the gas valve as needed (matches the original). Muzzle device will not be included (griffin OTB). Have about 150 rounds through it. Comes in the original case etc. No Trades*


$3500 Shipped

Searching for insight on an incident I had with my Tavor 7 paired with an RC2 7.62 which in turn led to a baffle strike. (haha he bonked his can what an idiot)

The Tavor 7 barrel has that locking nut that is used with its muzzle devices which causes a lot of "run out"? Not sure if that is the correct term but a lot of threads left in the muzzle device that don't thread onto the barrel due to having to engage the locking nut to time and tighten the muzzle device to the barrel. The muzzle device used was the surefire socom brake used to quick attach the RC2 7.62.

So I fit the brake to the gun and zero an eotech. Works great. I then shoot several subs (15-20) through the suppressor landing them on target to a steel plate. Everything working as intended, no problems. Then I load up some sellier and bellot NATO 147gr. First supersonic round misses off target and my friend and I are perplexed. Inspecting the can we notice the obvious but small mark of brass from the projectile, we can see the last two baffles and the end cap have barely been struck by the brass leaving the obvious mark on the endcap.

Now right before this cartridge was fired we were changing the gas settings on the Tavor 7. As per the manual the gas system is designed to be adjusted by sticking a 7.62 cartridge in and turning the gas adjuster/key(?) to the desired setting. Now when I had first received the gun I tested this with the same s&b nato 147 grain ammo and actually separated the projectile from the cartridge. Not the best system imo.

So did I accidently cant or angle the projectile while doing this, in turn making the projectile all *warbly* causing the baffle strike? Or was this caused by the run out of the muzzle brake not being able to be threaded onto the barrel as much as perhaps an AR10 barrel? I've heard rumor of this runout being a potential for baffle strikes. I do have a couple RC2 cans and have never attached them incorrectly, it would be hard to do so imo.

Out of frustration we continued to shoot the 147 nato round after re-attaching the can and inspecting the unfired rounds. We continuously missed the target we were using to zero. The surefire rep who I spoke with said this means we were still having baffle strikes if we were still missing. I'm a little lost and searching for insight. All the subs ran fine and hit on target, none of the supers hit and we couldn't even tell where they were landing. Is the RC2 not meant for the Tavor? Should some sort of direct thread can be used instead?

Any insights, thoughts, or jokes welcome below.

Last bit of 6.5 Creedmoor Brass that I have.
All Hornady . Fired from a bolt gun
Actual ONCE fired
500 pcs for $160 shipped
Thanks for looking
Cross listed

I thought this was an interesting YouTube series this guy has going. Cool to see all the different rigs.
Might not be as entertaining to some more seasoned shooters, but I think it’s fun.

Login to view embedded media

Badger Ordnance M2013 Action with new unfired Proof Research 1:10 Carbon Fiber Barrel and a Triggertech Diamond Pro Curve Trigger. Rifle sits in a Manners T6 Gap Camo stock with Mini Chassis. Action had less than 200 rounds before rebarreling to this .308. Rifle weights 8lbs 10oz. $2800 shipped for the package. Would sell stock separately if and on IF, someone buys the barreled first!

green338XFirst Sergeant
Rating: 3.1/5 this site
1034 posts this site
308 AR/AR10 Build Info/Picture Thread
10/13/2014 Last edited 10/13/2014 by green338
(2 votes)

---

Let's see your gassers!



Here's one of my ex's

Mega Maten Monolithic receiver sets

GA Precision GAP-10 barrel 20" w/ BO Brake

Magpul PRS stock w/ JP SCS

Geissele SDE Trigger

Spuhr Mount

Schmidt & Bender 5-25 MRAD DT CCW XR



[IMG2=JSON]{"alt":" photo DSC03524_zps477a6cdd.jpg","data-align":"none","data-size":"full","src":"http:\/\/i892.photobucket.com\/albums\/ac129\/green122\/DSC03524_zps477a6cdd.jpg"}[/IMG2]

Rate now:
wareagle700

XFirst Sergeant
Rating: 3.7/5 this site
1317 posts this site
Re: 308 AR/AR10 Build Info/Picture Thread
10/14/2014 Last edited 10/29/2014 by wareagle700
(2 votes)

---

Very nice sir.

My .308:

MEGA MA-10 Receivers
JP 15" Handguard
Badger Brake
Syrac Adjustable Gas Block
Lilja barrel cut to 17.5" from 20" (rifle length gas)
JP LMOS bolt carrier group
JP SCS recoil system
Geissele SSA-E Trigger
Magpul ACS stock
Nightforce 3.5-15x50 in a Nightforce Unimount

This is the smoothest shooting .308 I have ever shot. Accuracy is as good as I can ask for.

Got a 22 cal 1:7 mtu ready for someone’s next 22gt or something fun. 28 incher so can be cut to whatever you’d like. Cryo treated as well. Asking 500

Time to do some spring cleaning. Selling my brand new never been opened 4-28. Have mkm flip caps and a accuracy first bubble level going with it. It is for sale not on sale but with it never seen the sun or anything i feel is fair. Asking 3200 for the package. Have plenty of vouches. View attachment IMG_7183.jpegView attachment IMG_7184.jpegView attachment IMG_7185.jpegView attachment IMG_7186.jpeg
View attachment IMG_7182.jpeg

Vortex AR prism.
Great condition.
$175 shipped.