Magpul Pro700 Chassis Video

[EchoDeltaSierra]

Last Sunday I shot my first match with the Pro 700 chassis. I'm running the more vertical grip and have it spaced where I get 90 degree finger-pad contact on the trigger. The thumb shelf quickly became the natural index point for my grip. After running it hard for a 100-round match, I like the chassis even more.

 

[Dthomas3523]

So it looks like the Ingenuity gunworks rail will work, he told me to get the MLOK one for Seekins, and it should go to the rear far enough.

Anyone tried this or seen/have any pics of the ingenuity rail on the pro700?

 

[Tactical Taz]

Not the ingenuity rail, but the sawtooth rail made for the 15" seekins handguard should be pretty similar. That is what I am running in my previous post. I will try to get some better pictures of it sometime.

 

[SuperSneakySniper]

Anyone tried this or seen/have any pics of the ingenuity rail on the pro700?

I plan to use this setup. Unfortunately i wont have it all together until mid-late november. Ill be sure to post pics though

 

[TVLLIVS]

Doubtful on that ill cut plastic before I file a cocking sear. Well see tomorrow. Fedex normally is at my place around 1

Graciously awaiting some good news lol.

 

[matleez]

Graciously awaiting some good news lol.

So when I tq the action down it rubs slightly. I'm going to take the chassis to work and mill out a few thousandths and see what we have. I can still run the bolt but its dragging and I'm sure it's not good for the cocking sear. Will update tomorrow. But other than that it looks awesome. Mag latch needs about .01 taken off to seat aw mags. I'll do that at work too

 

[TVLLIVS]

Awesome, do post some pics.

 

[matleez]

Yea I will. At a security gig at a haunted house so it will be about 4 hours or tomorrow when I do

 

[TVLLIVS]

Yea I will. At a security gig at a haunted house so it will be about 4 hours or tomorrow when I do

A few thousandths doesn't sound too bad. The sear doesn't contact the hinge button though right?

 

[matleez]

A few thousandths doesn't sound too bad. The sear doesn't contact the hinge button though right?

Just barely. It's not even scratching the anodizing on the bottom

 

[matleez]

Here. Barely scratching the anodizing

 

[matleez]

So dealing with the ultimatum. 3/16 bit at about. 02 deep took care of the cocking sear dragging. Next came the mag catch. Absolutely a pain in the ass. I couldn't get the pin in mine to budge so I hit it with a dremel from the top. It worked and my aw mag latches and has wiggle room and drops free. Next a part where they said may be a problem was the trigger hanger itself. Barely made contact and left some rub Mark's so I did some light dremel work and bam. So all in all not bad but requires some work which I was aware of going in.

 

[TVLLIVS]

Thanks for the pics, you definitely helped me make my decision. I ended up canceling my order on the Pro 700 and got a Masterpiece arms chassis instead. I just didn't see the point in spending the cash on a chassis that'd give me that much of a headache. Other then needing the mag catch shortened sightly, the Masterpiece Arms is pretty much drop-in.

 

[matleez]

yea, as of now i like this more than a MPA especially with the fact the thumb shelf is ambi so weakside shots still have the same grip style

 

[Dthomas3523]

Any impact action owners ran this chassis yet?

Drop in? Do magpul aics mags run without needing any work?

 

[SuperSneakySniper]

Any impact action owners ran this chassis yet?

Drop in? Do magpul aics mags run without needing any work?

I put my impact in no problem! However... Lots of friction running the included magpul ac 5rnd magazine. I didnt try modifying the magazine though, feed lips could probably be filed down.