What chassis are available with fully adjustable butt pad? Mainly wanting ability to cant for rem 700 footprint.
Chassis list, best adjustability...
- Thread starter Yooper3402
- Start date
I am really happy with my MDT LSS-XL Gen2
Attachments
If you’re looking to specifically cant the butt the most adjustable in that department is going to be an AX chassis. Not a great comp chassis but I don’t know if you’re into that or not. The KRG W3 will let you and so will the MDT ACC. Neither as much as the Ax tho.
You can get adjustable butt pads installed in any stock.
I have a one in my Kelbly KTS fiberglass stock.
I also like what MDT ACC has to offer. Very adjustable.
mdttac.com
Last I can think of is the XLR has adaptability to use ANY AR style stock.
lOTS OF OPTIONS!
GL
DT
I have a one in my Kelbly KTS fiberglass stock.
I also like what MDT ACC has to offer. Very adjustable.
ACC Premier Chassis System
The MDT ACC Premier Chassis System was created with an integrated weight management system, allowing shooters to fine-tune their chassis’ weight and balance point. Add weights to the buttstock as well as the forend on both the interior and exterior.
mdttac.com
Last I can think of is the XLR has adaptability to use ANY AR style stock.
lOTS OF OPTIONS!
GL
DT
i cannot complain about my mdt chassis except they all look about the same they are pretty adjustable It works so Its all good .
Magpul is plenty adjustable: buttpad height, cant and LOP. Can even move the cheek riser forward and back.
Hi 10Ring1,
My little piglet weighs in at a hair over 18 lbs. as you see her.
I have actually considering adding some more weight by sandwiching the weights. Stacking them
atop each other. I think I could do it with longer screws for the M-loc's. As I say that, I can go to Lowes and get some longer screws and try it out with my existing weights from another area. It may be enough to just redistribute the mass. How cool is that !! Thanks for getting my brain working.
If I don't like that, I could certainly use 3M dual lock. It is like super Velcro. If you have never used it,
you should get some just to try out. You will find uses for it. It is great stuff.
You can even get it in shapes that have holes for fastening it down. In that application, you need not count on adhesive. That was an under water solution related to scuba diving equipment.
Shawn
Attachments
Any KRG product with the optional 4-way buttplate adjuster
#1 easily goes to the AX but in my opinion comes at the cost of the grip.
Next I would put the MPA BA chassis because it has a bunch of holes for repositioning the pad but the process is years compared to the AX. I’m sure other flavors of MPA do as well.
Subjective option (but in last place) would be the Whiskey 3 or other KRG chassis after purchasing the adjustable butt pad. This one lets you lock in left or right cant at a fixed position. Lacks the in between positions that the first two can provide.
Next I would put the MPA BA chassis because it has a bunch of holes for repositioning the pad but the process is years compared to the AX. I’m sure other flavors of MPA do as well.
Subjective option (but in last place) would be the Whiskey 3 or other KRG chassis after purchasing the adjustable butt pad. This one lets you lock in left or right cant at a fixed position. Lacks the in between positions that the first two can provide.
A large part of why I chose my MDT LSS is that the top of the chassis is open and that allows for
a large scope bell and lower mounting. Also, I had a max bbl length of 22" and it would have looked stupid in a ACC. I considered all that I could given my zero chassis knowledge. I also nearly missed the channel width. My bbl contour is very wide at the action and needs all that the LSS has available.
Shawn
I like my Magpul stock as well. Lots of adjustments. I even put it on my KRISS Defiance in the second photo. I like the other Magpul goodies as well. The BAD lever, Trigger guard, Extended mag release.
The Yankee hill pull pins are also very nice. And the charging handle latch in the last photo is the bomb.
All of it's edges are well rounded and it feels great against my girly engineer hands.LoL
Shawn
Attachments
You will not find a better chassis for the money. Buttpad adjustable for lop, height, and cant.
bergara.bpishopping.com
BERGARA BMP CHASSIS
bergara.bpishopping.com
I will have to revisit the Magpul site to recall what chassis that they offer that I passed on for my V22 build. I do recall that I could have put the Magpul PRS butt stock on my MTD chassis but the MTD short rifle butt stock had more adjustability. And the look of it flows much better as well.
Shawn
PDC Custom offers LOP, cheek, butt height and butt tilt on their chassis. I have had a few of them, and have been very happy overall. I'm currently running the Gen5 Competition. The website is down, though, so you'll have to look at the Facebook page for photos.
KRG Bravo with tool-less adjustable butt pad adjustable for height, cant, and LOP.
kineticresearchgroup.com
kineticresearchgroup.com
Bravo Chassis – Kinetic Research Group
kineticresearchgroup.com
Tool-less Buttpad Height Mechanism – Kinetic Research Group
kineticresearchgroup.com
You will not find a better chassis for the money. Buttpad adjustable for lop, height, and cant.
BERGARA BMP CHASSIS
Hard to find info on the Bergara BMP chassis. I like that it is 7075 aluminum. Price seems awesome for what it is.
Does Bergara make it themselves or have some else make it for them?
Last edited:
