Recent content by Bugholes

  1. Bugholes

    RPR 338 LAPUA BARREL

    Im sure that there are plenty of places that will make you an RPR barrel. Be aware that the magnum frame RPR requires the use of a 1.35" diameter blank to make a replacement barrel. The barrel also needs to be 1.2 max (I believe) in front of the flange so you would need to either special order...
  2. Bugholes

    Escutcheons for bedding Manners ELR light stock

    we make an escutcheon for our own stock work (not on the website), its from stainless barrel pieces. If youre interested call Russ and he can get you one
  3. Bugholes

    Trouble shooting - Impact 737 - MDT HNT26 - AW Magazines

    You need to mention what cartridge you’ve running please Also cartridges should be touching the feed lip for the length of the lip. If the base is too low you may need to open the front to let the case head rise up higher Edited for clarity
  4. Bugholes

    When is a chamber too large?

    If your die used to size 308 cases correctly with normal effort, and it’s struggling to resize cases from this new chamber in question, and your using similar/same brass, you should probably contact the gunsmith
  5. Bugholes

    SOLD WTB: 2 Port Self-timing brake, 30 Cal, 5/8-24. (Bugholes or Hellfire)

    We have a few 30cal BugBrakes in stock. If the website says we’re out give Russ a call and he’ll get one for you
  6. Bugholes

    When is a chamber too large?

    if its .001 to .002 over the reamer size thats not enough to affect accuracy. Shouldnt be enough to cause the sizing issues youre experiencing. Most guys with manual lathes have their tailstock off the spindle axis (high, low, left,right, whatever) and getting a chamber .001 or more over the...
  7. Bugholes

    Accuracy International 223 conversion working

    when we install a 223 head we do not use epoxy or thread locker of any kind. The fitment is a slip fit, almost press fit
  8. Bugholes

    Accuracy International 223 conversion working

    the Ai factory bolts do have some sort of epoxy or thread locker between the head and bolt body
  9. Bugholes

    Accuracy International 223 conversion working

    It is completely reversible. Remove the SFP fire control and punch (3) roll pins to change the bolt head. Removal and reinstallation of the pins is straightforward but it has its pitfalls. You can get a pin cross-stuck in the bore of the bolt, and the pins need to be re-installed at a very...
  10. Bugholes

    Accuracy International 223 conversion working

    weve received all the bolts we had on order, took at least 2 years, these bolts are all gone. With the bolt availability and the fiddle-fucking around we need to do with each and every system, were probably gonna let it run its course and retire it. Im not planning on doing another run of...
  11. Bugholes

    Keeping Suppressors Cool

    https://www.makitatools.com/products/tools/cordless/18v-lxt/fans
  12. Bugholes

    SOLD WTS/WTT New Swarovski BTX with 95mm objective

    It doesn’t get any better than this…
  13. Bugholes

    Removing AI Rifle Folding Catches

    You might as well just order replacement parts (cross bolt and nib), then grab the nib with vise grips
  14. Bugholes

    Removing AI Rifle Folding Catches

    The fastener goes through the flush cup, through the chassis body, and threads into the folding butt retaining nib. The nib has a radial hole through it so you can get a punch or hex key (sideways) for leverage. If the hex head in the flush cup fastener is stripped then you can try lightly...