Recent content by ejg

  1. E

    Tikka T3 Thread

    Plenty sporter 30 cal rifles are fitted with ~16.5mm muzzle diameter and use M14x1 muzzle thread but recently I am sure Sako are using M15x1 even up to 9.3x62. They seem to be happy with the small shoulder. I had an expert rifle smith fit a Suppressor using M16x1 on a 16.5mm Lothar Walther...
  2. E

    Strasser RS 700: straight pull Remage-style barrel nut that uses R700 accessories (stocks, triggers)

    A good friend was planning on getting into PRS but also had a thing for straight pull rifles and wanted to try one. We said the only one I would try is the Strasser S700. We ordered a Barrelled action with the 26" 6.5CM option. Our friend wanted to use a PSE E-Tac carbon stock as he is using one...
  3. E

    Precision Rifles.....show em!!

    Yesterdays hunt. Took my 300wm with Atlasworx M5 3.85 CIP floorplate and MDT 3 shot Polymer mag. PSE Evolution stock, 24" Proof Sendero light, 4-16x50 PMII, Spartan Tac bipod and Spuhr hunting mounts/rail. 9lb including scope. edi
  4. E

    Tikka T3 Thread

    Well spotted. edi
  5. E

    Tikka T3 Thread

    as in original T3 Lite plastic magazines? I tried using the 30-06 version for a 308 and it wasn't ideal. Not very reliable if I remember right. edi
  6. E

    Tikka T3 Thread

    One of our customers used his 20" stainless CTR in 6.5CM at the Guardian PR in Ireland 2018.. They shot clays in the sand bank at 1200yds, he hit a few with Hornady factory ammo. 20" is by far not ideal but gets there. edi
  7. E

    Tikka T3 Thread

    Recon Tikka is just at the end of their factory capacity and can't keep up with demand. About time someone produces a T3 clone not some improved version... that no one wants. edi
  8. E

    Tikka actions

    Barrel speed of my 20" Stainless 308 CTR's and a 20" blued T3 Lite 308 were the same as a 20" blued Lothar Walther 308 barrel 1/12 we also have. Our 1/13 Bartlein Palma possibly tight bore also 20" was slightly faster. Also our 1/13 Lilja 20" Palma seemed a bit faster. edi
  9. E

    Tikka actions

    Only speed I have in my head is from a stock CTR ~24" doing 2730fps with Sako TRG 136gr ammo. Still have a few boxes of the same batch and would like to test in 22" and 26" Lothar Walther barrels in RS700 as well as a 22" carbon Proof T3 which are new. edi
  10. E

    Tikka actions

    I love t3 actions however if it comes to long action cartridges I'd go rem 700 / rem clone. The T3 action is just a bit short. You can get a 3.715 AI mag system fitted and work ok if you cut out a bit of the ramp but not the CIP length 3.85" which will also take the 3 shot MDT polymer mags...
  11. E

    Tikka T3 Thread

    They are very rigid and strong, have a double monocoque design. No milling involved. Internal alu in areas where fittings go. Carbon shell inside the barrel channel as well as inlet and cheek raiser opening. No hollow areas. Yesterdays hunt, with two Danish friends, one of them a LE weapons...
  12. E

    Tikka T3 Thread

    I am somewhat involved with the technology of the product as well as user/tester and therefore won't go into details. The stock is made with complex technologies which might be different to what is there at the moment. edi
  13. E

    Tikka T3 Thread

    Not tried a 6mm Creed yet but have 308 and 6.5 CM which work well out of all MDT mags I have including the 3 shot MDT. That stock does not have an integrated rail, just flat bottom but can take various arca rails. edi
  14. E

    Tikka T3 Thread

    Atlasworx Australia makes an Aics mag system that fits into standard CTR footprint stocks. They left the release lever a bit too long so that mag fit can be fine tuned which is sensible. Sitting in an Evolution stock from Ireland with flush fitting MDT 3 shot mag, other AICS also fit. edi
  15. E

    Tikka T3 Thread

    Always grease the cam. Try opening both action screws by one or two turns and check if the bolt opens easier. Either screw if too long could interfere. edi
See more
Top Bottom
Back
Home
Forums
Merch
Alerts