Recent content by flyer1a

  1. flyer1a

    Area419 - The ULTIMATE TEST - 2025 Big Boy Precision Optic Shootout

    We didn't sell any optics at all for many years. We decided to sell them again for two reasons - 1) Making rings and mounts, it's logical, and 2) We started with them because we thought this new Kahles was crazy and would move quickly. You'll see us, over the course of the next 6 months, add a...
  2. flyer1a

    Area419 - The ULTIMATE TEST - 2025 Big Boy Precision Optic Shootout

    The internet loves to stand in a circle and chant "FIGHT, FIGHT, FIGHT" though I much prefer the idea of "GET BETTER, GET BETTER, GET BETTER" I'm in when you are, I'll drink extra coffee for your midnight stream.
  3. flyer1a

    Area419 - The ULTIMATE TEST - 2025 Big Boy Precision Optic Shootout

    If there's something you've done in this style that I'd overlooked, by all means that's on me. I'll email you though, I have another one in mind that I might pick your brain about, VERY much in your wheelhouse. I'm sure SnipersHide will hate it, but I think it could be cool.
  4. flyer1a

    One Piece Scope Mounts ..What do you use?

    That's correct, this is for the base/rail connection, NOT the caps. The caps are still listed (and will continue to be listed) at 18 in-lb, though if you use the 20 in-lb Fix-It Stick you'll not hurt anything.
  5. flyer1a

    One Piece Scope Mounts ..What do you use?

    When we cycle through the packaging. Initially when we made the mounts we set a lower number to be conservative. Over ongoing testing and abuse, the 45in-lb number gives greater security with no downside. We make rolling improvements, however small, on products constantly. It's actually...
  6. flyer1a

    Area 419 Micrometer Adjustable Sizing Dies

    To clarify, the S-Series dies adjust the same as any other common die on the market. Screw it in a little more or less, and you can adjust. Of course we think a solution like our Modular Shellholder kit with headspace adjustment in the inserts is ideal, or something like the Redding...
  7. flyer1a

    One Piece Scope Mounts ..What do you use?

    Nope, the fastners are all T20. Interested to know where you saw the T25 so I can correct it.
  8. flyer1a

    Mounts - Gray Ops vs Area 419

    Email me images of what you're talking about, if possible. I'm curious as to what you have going on here. Craig(at)Area419(dot)com
  9. flyer1a

    Mounts - Gray Ops vs Area 419

    Aluminum oxide, while quite hard, does not build into a shell, rather stays in a very fine form without meaningful structure. Bare aluminum builds a surface oxide layer almost instantly when raw aluminum is exposed to oxygen.
  10. flyer1a

    Mounts - Gray Ops vs Area 419

    So I stumbled across something this week - acetone is fine, and does a decent job, but WD-40 is what you really want. If you get aluminum transfer, wipe it off with WD-40, then degrease, and it's a brand new optic. Absolute magic.
  11. flyer1a

    Area 419 Zero Press vs SCA Nexus Press

    Stan is a great dude and does very good work. They'll serve you well for a lifetime.
  12. flyer1a

    Area 419 Micrometer Adjustable Sizing Dies

    Oh, never saw this to respond. @JSW2000 noted that it IS hard contact with the die/shellholder. Also, the mandrels are interchangeable to different diameters so you can set different neck tensions.
  13. flyer1a

    Area 419 Micrometer Adjustable Sizing Dies

    Correct, we are not making and do not plan to do bushings. We think a single-piece sizing body is a better option. And if someone gets upset about that position, it's really ok. There are other options that provide this.
  14. flyer1a

    Area 419 Zero Press vs SCA Nexus Press

    Screw your die in a little further. We note this specifically in die setup videos but it is often overlooked. TO INSTALL: 1) Ram in the up position 2) Screw die all the way down 3) Drop the ram 4) Screw in 1/4 additional turn And then size. This should get you very close to where you need to...
  15. flyer1a

    Mounts - Gray Ops vs Area 419

    At the rail? No. Though it makes it mostly irrelevant as the mounting surface for the optic is aligned by the bridge between ring sections. So the whole mount can be off, but the mounting surfaces for the optic will remain true to one another and keep stress out of the connection.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts